NAME
mpstat - Report processors related statistics.
SYNOPSIS
mpstat [ -A ] [ -I { SUM | CPU | ALL } ] [ -u ] [ -P { cpu [,...] | ON | ALL } ] [ -V ] [ interval [ count ] ]
DESCRIPTION
The mpstat command writes to standard output activities for each available processor, processor 0 being the first one.
Global average activities among all processors are also reported. The mpstat command can be used both on SMP and UP
machines, but in the latter, only global average activities will be printed. If no activity has been selected, then the
default report is the CPU utilization report.
The interval parameter specifies the amount of time in seconds between each report. A value of 0 (or no parameters at all)
indicates that processors statistics are to be reported for the time since system startup (boot). The count parameter can
be specified in conjunction with the interval parameter if this one is not set to zero. The value of count determines the
number of reports generated at interval seconds apart. If the interval parameter is specified without the count parameter,
the mpstat command generates reports continuously.
OPTIONS
-A This option is equivalent to specifying -I ALL -u -P ALL
-I { SUM | CPU | ALL }
Report interrupts statistics.
With the SUM keyword, the mpstat command reports the total number of interrupts per processor. The following values
are displayed:
CPU
Processor number. The keyword all indicates that statistics are calculated as averages among all processors.
intr/s
Show the total number of interrupts received per second by the CPU or CPUs.
With the CPU keyword, the number of each individual interrupt received per second by the CPU or CPUs is displayed.
The ALL keyword is equivalent to specifying all the keywords above and therefore all the interrupts statistics are
displayed.
-P { cpu [,...] | ON | ALL }
Indicate the processor number for which statistics are to be reported. cpu is the processor number. Note that pro-
cessor 0 is the first processor. The ON keyword indicates that statistics are to be reported for every online pro-
cessor, whereas the ALL keyword indicates that statistics are to be reported for all processors.
-u Report CPU utilization. The following values are displayed:
CPU
Processor number. The keyword all indicates that statistics are calculated as averages among all processors.
%usr
Show the percentage of CPU utilization that occurred while executing at the user level (application).
%nice
Show the percentage of CPU utilization that occurred while executing at the user level with nice priority.
%sys
Show the percentage of CPU utilization that occurred while executing at the system level (kernel). Note that
this does not include time spent servicing hardware and software interrupts.
%iowait
Show the percentage of time that the CPU or CPUs were idle during which the system had an outstanding disk I/O
request.
%irq
Show the percentage of time spent by the CPU or CPUs to service hardware interrupts.
%soft
Show the percentage of time spent by the CPU or CPUs to service software interrupts.
%steal
Show the percentage of time spent in involuntary wait by the virtual CPU or CPUs while the hypervisor was ser-
vicing another virtual processor.
%guest
Show the percentage of time spent by the CPU or CPUs to run a virtual processor.
%idle
Show the percentage of time that the CPU or CPUs were idle and the system did not have an outstanding disk I/O
request.
Note: On SMP machines a processor that does not have any activity at all is a disabled (offline) processor.
-V Print version number then exit.
EXAMPLES
mpstat 2 5
Display five reports of global statistics among all processors at two second intervals.
mpstat -P ALL 2 5
Display five reports of statistics for all processors at two second intervals.
[root@netqh110 ~]# cat /proc/cpuinfo |grep -i processor | head -n 5 #check logical cpu
processor : 0
processor : 1
processor : 2
processor : 3
processor : 4
[root@netqh110 ~]# mpstat -P 0 #check special cpu related statistics which you defined.
Linux 2.6.32-279.el6.x86_64 (netqh110.qrow.netfinity.com) 07/31/2012 _x86_64_ (32 CPU)
01:40:41 PM CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
01:40:41 PM 0 0.33 0.00 0.21 0.01 0.00 0.02 0.00 0.00 99.42
[root@netqh110 ~]# mpstat -P 1
Linux 2.6.32-279.el6.x86_64 (netqh110.qrow.netfinity.com) 07/31/2012 _x86_64_ (32 CPU)
01:40:46 PM CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
01:40:46 PM 1 0.09 0.00 0.09 0.00 0.00 0.01 0.00 0.00 99.81
[root@netqh110 ~]# mpstat -P ALL
Linux 2.6.32-279.el6.x86_64 (netqh110.qrow.netfinity.com) 07/31/2012 _x86_64_ (32 CPU)
01:43:59 PM CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
01:43:59 PM all 0.07 0.00 0.10 0.00 0.00 0.00 0.00 0.00 99.83
01:43:59 PM 0 0.33 0.00 0.21 0.01 0.00 0.02 0.00 0.00 99.42
01:43:59 PM 1 0.09 0.00 0.09 0.00 0.00 0.01 0.00 0.00 99.81
01:43:59 PM 2 0.03 0.00 0.02 0.00 0.00 0.00 0.00 0.00 99.95
Linux/Unix mpstat command
發表評論
所有評論
還沒有人評論,想成為第一個評論的人麼? 請在上方評論欄輸入並且點擊發布.
相關文章
WebLogic是怎樣判斷堵塞線程(Stuck Thread)和獨佔線程(Hogging Thread)的
LampthNeo
2019-02-23 13:04:28
Prime_DSC_MentionCalcSpark性能調優
誰伴我闖蕩
2019-02-22 19:31:40
性能調優-SQL TRACE
vicky_009
2019-02-22 18:03:29
SparkStreaming 性能調優
ChinaUnicom110
2019-02-22 14:04:08
tomcat 性能調優
aishangwei
2019-02-22 13:46:17
獨家解密:阿里大規模數據中心性能分析
作者:郭健美
2019-02-19 06:44:13
前端tree優化實踐:渲染速度從14.65s到0.49s
杨涛峰
2019-02-15 10:23:58
2019年最好用的6款數據庫監控工具
Renaud Larue-Langlois
2019-02-05 09:03:55
前端技術選型的遺憾和經驗教訓
Max
2019-02-01 08:03:57
Nginx 學習書單整理
陶辉
2019-01-29 14:39:00
實時監控系統如何幫助FreeWheel支持超級賽事直播廣告
Debra
2019-01-08 13:53:53
進階 Nginx 高手必須跨越的 5 座大山
陶辉
2018-12-26 16:24:02