bluefish - 51CTO技術博客----------本文轉自網上，如果原作看到的話請留言，我會把出處加上，謝謝！
在STM32中用到了Cortex-M3定義的三組寄存器，有關這三組寄存器的說明不在STM32的技術手冊中，需要參考ARM公司發佈的Cortex-M3 Technical Reference Manual (r2p0)。
在STM32的固件庫中定義了三個結構體與這三個寄存器組相對應，這三個結構體與ARM手冊中寄存器的對應關係如下：
一、NVIC寄存器組
STM32的固件庫中有如下定義：
typedef struct
{
vu32 ISER[2];
u32 RESERVED0[30];
vu32 ICER[2];
u32 RSERVED1[30];
vu32 ISPR[2];
u32 RESERVED2[30];
vu32 ICPR[2];
u32 RESERVED3[30];
vu32 IABR[2];
u32 RESERVED4[62];
vu32 IPR[11];
} NVIC_TypeDef;
它們對應ARM手冊中的名稱爲
ISER = Interrupt Set-Enable Registers
ICER = Interrupt Clear-Enable Registers
ISPR = Interrupt Set-Pending Register
ICPR = Interrupt Clear-Pending Register
IABR = Active Bit Register
IPR = Interrupt Priority Registers
每個寄存器有240位，以Interrupt Set-Enable Registers說明，ISER[0]對應中斷源0~31，ISER[1]對應中斷源32~63，STM32只有60箇中斷源，所以沒有ISER[2:7]。
參考STM32技術參考手冊中的中斷向量表，中斷源的位置爲：
位置0 - WWDG = Window Watchdog interrupt
位置1 - PVD = PVD through EXTI Line detection interrupt
位置2 - TAMPER = Tamper interrupt
......
位置58 - DMA2_Channel3 = DMA2 Channel3 global interrupt
位置59 - DMA2_Channel4_5 = DMA2 Channel4 and DMA2 Channel5 global interrupts
二、系統控制寄存器組
STM32的固件庫中有如下定義：
typedef struct
{
vuc32 CPUID;
vu32 ICSR;
vu32 VTOR;
vu32 AIRCR;
vu32 SCR;
vu32 CCR;
vu32 SHPR[3];
vu32 SHCSR;
vu32 CFSR;
vu32 HFSR;
vu32 DFSR;
vu32 MMFAR;
vu32 BFAR;
vu32 AFSR;
} SCB_TypeDef; /* System Control Block Structure */
它們對應ARM手冊中的名稱爲
CPUID = CPUID Base Register
ICSR = Interrupt Control State Register
VTOR = Vector Table Offset Register
AIRCR = Application Interrupt/Reset Control Register
SCR = System Control Register
CCR = Configuration Control Register
SHPR = System Handlers Priority Register
SHCSR = System Handler Control and State Register
CFSR = Configurable Fault Status Registers
HFSR = Hard Fault Status Register
DFSR = Debug Fault Status Register
MMFAR = Mem Manage Address Register
BFAR = Bus Fault Address Register
AFSR = Auxiliary Fault Status Register
三、系統時鐘寄存器組
STM32的固件庫中有如下定義：
typedef struct
{
vu32 CTRL;
vu32 LOAD;
vu32 VAL;
vuc32 CALIB;
} SysTick_TypeDef;
它們對應ARM手冊中的名稱爲
CTRL = SysTick Control and Status Register
LOAD = SysTick Reload Value Register
VAL = SysTick Current Value Register
CALIB = SysTick Calibration Value Register