交換機是cisco3550-24三層交換機，24口進100兆帶寬，1口，2口，3口每個口出帶寬限25兆，這些資料夠了嘛
24口上面的網關ip是218.20.252.241，1口下面的ip是218.20.252.242，2口下面的ip是218.20.252.243，3口下面ip是218.20.252.244，我這臺機的ip218.20.252.254，掩碼是255.255.255.240
Switch#sh run
Building configuration...
Current configuration : 3239 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Switch
!
enable password cisco
!
no aaa new-model
ip subnet-zero
ip routing
!
mls qos aggregate-policer user1-in 25000000 2000000 exceed-action drop
mls qos
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
vlan internal allocation policy ascending
!
class-map match-all match-alluser1-in
match ip dscp default
!
!
policy-map 10
class match-alluser1-in
police aggregate user1-in
!
!
!
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 632
switchport mode trunk
service-policy input 10
service-policy output 10
!
interface FastEthernet0/2
switchport access vlan 632
switchport mode dynamic desirable
service-policy input 10
service-policy output 10
!
interface FastEthernet0/3
switchport access vlan 632
switchport mode dynamic desirable
service-policy input 10
service-policy output 10
!
interface FastEthernet0/4
switchport access vlan 2
switchport mode dynamic desirable
!
interface FastEthernet0/5
switchport access vlan 632
switchport mode dynamic desirable
service-policy input 10
service-policy output 10
!
interface FastEthernet0/6
switchport mode dynamic desirable
!
interface FastEthernet0/7
switchport mode dynamic desirable
!
interface FastEthernet0/8
switchport access vlan 3
switchport mode dynamic desirable
!
interface FastEthernet0/9
switchport mode dynamic desirable
!
interface FastEthernet0/10
switchport mode dynamic desirable
!
interface FastEthernet0/11
switchport mode dynamic desirable
!
interface FastEthernet0/12
no switchport
ip address 192.168.200.1 255.255.255.0
ip policy route-map test
!
interface FastEthernet0/13
switchport mode dynamic desirable
!
interface FastEthernet0/14
switchport mode dynamic desirable
!
interface FastEthernet0/15
switchport mode dynamic desirable
!
interface FastEthernet0/16
switchport mode dynamic desirable
!
interface FastEthernet0/17
switchport mode dynamic desirable
!
interface FastEthernet0/18
switchport mode dynamic desirable
!
interface FastEthernet0/19
switchport mode dynamic desirable
!
interface FastEthernet0/20
switchport mode dynamic desirable
!
interface FastEthernet0/21
switchport mode dynamic desirable
!
interface FastEthernet0/22
switchport mode dynamic desirable
!
interface FastEthernet0/23
switchport mode dynamic desirable
!
interface FastEthernet0/24
switchport trunk encapsulation dot1q
switchport trunk native vlan 632
switchport mode trunk
!
interface GigabitEthernet0/1
switchport mode dynamic desirable
!
interface GigabitEthernet0/2
switchport mode dynamic desirable
!
interface Vlan1
no ip address
!
interface Vlan2
ip address 192.168.0.1 255.255.255.0
!
interface Vlan3
ip address 192.168.1.1 255.255.255.0
!
interface Vlan100
no ip address
!
interface Vlan632
ip address 218.20.252.254 255.255.255.240
!
ip classless
ip route 0.0.0.0 0.0.0.0 218.20.252.241
ip http server
ip http secure-server
!
!
!
!
route-map test permit 112
match ip address 112
set ip next-hop 192.168.222.1
!
!
control-plane
!
!
line con 0
line vty 0 4
no login
line vty 5 15
no login
!
!
end
Switch#
案例二：
一、網絡說明
PC１接在Cisco3550 F0/1上，速率爲1Ｍ；
PC１接在Cisco3550 F0/2上，速率爲2Ｍ；
Cisco3550的G0/1爲出口。
二、詳細配置過程
注：每個接口每個方向只支持一個策略；一個策略可以用於多個接口。因此所有PC的下載速率的限制都應該定義在同一個策略(在本例子當中
爲policy -map user-down)，而PC不同速率的區分是在Class-map分別定義。
1、在交換機上啓動QOS
Switch(config)#mls qos //在交換機上啓動QOS
２、分別定義PC1(10.10.1.1)和PC2(10.10.2.1)訪問控制列表 Switch(config)#access-list 10 permit 10.10.1.0 0.0.0.255 //控制pc1上行流量
Switch(config)#access-list 100 permit any 10.10.1.0 0.0.0.255 //控制pc1下行流量
Switch(config)#access-list 11 permit 10.10.2.0 0.0.0.255 //控制pc2上行流量
Switch(config)#access-list 111 permit any 10.10.2.0 0.0.0.255 //控制pc2下行流量
３、定義類，並和上面定義的訪問控制列表綁定 Switch(config)# class-map user1-up //定義PC１上行的類，並綁定訪問列表10
Switch(config-cmap)# match access-group 10
Switch(config-cmap)# exit
Switch(config)# class-map user2-up
Switch(config-cmap)# match access-group 11 //定義PC2上行的類，並綁定訪問列表10
Switch(config-cmap)# exit
Switch(config)# class-map user1-down
Switch(config-cmap)# match access-group 100 //定義PC１下行的類，並綁定訪問列表100
Switch(config-cmap)# exit
Switch(config)# class-map user2-down
Switch(config-cmap)# match access-group 111 //定義PC2下行的類，並綁定訪問列表111
Switch(config-cmap)# exit
4、定義策略，把上面定義的類綁定到該策略 Switch(config)# policy-map user1-up //定義PC１上行的速率爲1M
Switch(config-pmap)# class user1-up
Switch(config-pmap-c)# trust dscp
Switch(config-pmap-c)# police 1024000 1024000 exceed-action drop
Switch(config)# policy-map user2-up //定義PC２上行的速率爲2M
Switch(config-pmap)# class user2-up
Switch(config-pmap-c)# trust dscp
Switch(config-pmap-c)# police 2048000 1024000 exceed-action drop
Switch(config)# policy-map user-down
Switch(config-pmap)# class user1-down
Switch(config-pmap-c)# trust dscp
Switch(config-pmap-c)# police 1024000 1024000 exceed-action drop
Switch(config-pmap-c)# exit
Switch(config-pmap)# class user2-down
Switch(config-pmap-c)# trust dscp
Switch(config-pmap-c)# police 2048000 1024000 exceed-action drop
Switch(config-pmap-c)# exit
５、在接口上運用策略 Switch(config)# interface f0/1
Switch(config-if)# service-policy input user1-up
Switch(config)# interface f0/2
Switch(config-if)# service-policy input user2-up
Switch(config)# interface g0/1
Switch(config-if)# service-policy input user-down