ifconfig命令详解

一、简单介绍

[root@nginx ~]# ifconfig

eth0(第一张网卡,第二张就是eth1)      

          Link encap:Ethernet(封装方式-以太网)  HWaddr 08:00:27:23:43:11(MAC地址)  

          inet addr:192.168.11.32(IP)  Bcast:192.168.11.255(广播)  Mask:255.255.255.0

          inet6 addr: fe80::a00:27ff:fe23:4311/64 Scope:Link (IPv6不用管)

          UP(当前状态) BROADCAST RUNNING MULTICAST  MTU:1500(最大存储单元,一次传输最大包)  Metric:1

          (接收的包)RX packets:275960 errors:0 dropped:0 overruns:0 frame:0

          (发送的包)TX packets:19786 errors:0 dropped:0 overruns:0 carrier:0

          co llisions:0(冲突数,不为0可能网络存在故障) txqueuelen:1000(缓冲器长度) 

          RX bytes:19362794 (18.4 MiB)  TX bytes:2371933 (2.2 MiB)


lo是本地环回地址,用于本地通信:

lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          inet6 addr: ::1/128 Scope:Host

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

二、用法   

NAME

       ifconfig - configure a network interface


SYNOPSIS

       ifconfig [interface]

       ifconfig interface [aftype] options | address ...

OPTIONS

       interface

              The  name of the interface.  This is usually a driver name followed by a unit number,

              for example eth0 for the first Ethernet interface.


       up     This flag causes the interface to be activated.  It is  implicitly  specified  if  an

              address is assigned to the interface.


       down   This flag causes the driver for this interface to be shut down.

三、常用使用案例:

  (1)[root@nginx ~]# ifconfig eth0  查看eth0的相关信息


  (2)[root@nginx ~]# ifconfig eth1 192.168.11.35 broadcast 192.168.11.255 netmask 255.255.255.0    配置IP地址,临时生效(一般去/etc/sysconfig/network-scripts下配置)


  (3) ifconfig eth0 down/up  临时开启或关闭网卡。


  (4)[root@nginx ~]# vim /etc/sysconfig/network-scripts/ifcfg-eth0    

     DEVICE=eth0   网卡设备的名称

     TYPE=Ethernet 封装类型

     UUID=eb80df38-3ca2-4cd0-87d6-f38c3054d092

     ONBOOT=yes    是否激活网卡,必须打开

     NM_CONTROLLED=yes

     BOOTPROTO=none   设置IP启动的方式,有static DHCP 不使用任何方式

     HWADDR=08:00:27:23:43:11  MAC地址 

     IPADDR=192.168.11.32      IP 

     PREFIX=24                 掩码

     GATEWAY=192.168.11.254    网关

     DNS1=61.128.128.68        DNS

     DEFROUTE=yes              

     IPV4_FAILURE_FATAL=yes

     IPV6INIT=no

     NAME="System eth0"

     该配置文件修改完成,需要重启网络服务:[root@nginx ~]# service network restart

  

發表評論
所有評論
還沒有人評論,想成為第一個評論的人麼? 請在上方評論欄輸入並且點擊發布.
相關文章