需要wps 2.0的幀結構，或者支持的競品。
On the wireless packet sniffer device, verify that the Selected Registrar flag, Device Password ID and Selected Registrar Configuration Methods attributes in the WSC IE of the Beacon and Probe Response frame are NOT present after the successful WSC handshake
需要如下設備
1. 支持生成4位PIN碼的客戶端；
2. 可配置爲EAP-WSC( supports EAP-WSC fragmentation )
3. 支持WPS2.0的設備
4.
4.1 Config APUT
4.1.1
如果WSC State的值爲0x01，則
The Probe Response frame from the APUT must include：Manufacturer, Model Name, Model Number, Serial Number, Device Name。
M2
Manufacturer, Model Name, Model Number, Serial Number, and Device Name. These attributes must not use NULL-padding, i.e., the last octet of the attribute value must not be 0x00。
uthentication Type Flags and Encryption Type Flags。
Connection Type Flags attribute。 The Connection Type Flags value shall be 0x01(ESS).
Device Password ID attribute
WSC State set to Configured (0x02)
目前存在的問題：Manufacturer 爲空 Primary Device Type爲空；
config method in M2，依然有一些問題，需要修改。應該改成：268C(Lable Pin, virual PIN/PBC, PHY PBC)
4.1.5 PBC walk time
爲了同步LCD，UI，我在WPS裏面把整個session的時間，從120 sec調整到了118秒，是否需要改回去。如果改回去的話，其他模塊是否需要修改，特別是GUI部分。
4.1.8
[測試步驟]
step 4. The internal Registrar must inform the user that security is not set and require confirmation or require explicit user operation to create this open network.
[GUI] 請李勇勇評估。
4.1.13 APUT correctly uses AuthorizedMACs subelement in the WFA Vendor Extension attribute in Beacons and Probe Responses
Test Requirement: The APUT must support PIN method. The APUT may support selection of the STA to commence the PIN registration process from a list on its user interface.
4.2
4.2.2
XXX 需要支持4位的Pin碼
4.2.4 Mixed mode test with PIN including whitespace and manually add a legacy WPA device,請GUI的同事注意。
4.2.10
[測試步驟]
3. Turn on STA2 and configure it to fragment EAP-WSC messages.
4. Read the PIN displayed on STA2 and enter the PIN in the internal Registrar on the APUT. The APUT must be able to complete WSC protocol withfragmented EAP-WSC messages.
我司是否有這樣的STA。
4.2.12 Check correctness of APUT association procedure
Test Requirement: ... The APUT must include the WSC IE in the 802.11 Association Response frame.The APUT must ignore the Privacy subfield of the Capability
information field in the Association Request frame. The APUT must ignore the RSN IE and the WPA IE if present in the Association Request frame. If the APUT supports WMM it must continue to comply with the WMM requirements.
The APUT must be backwards compatible and accept association from a version 1.0 WSC STA.
XXX，當前不支持在assoc response中含有WPS IE。
The APUT must ignore the RSN IE and the WPA IE if present in the Association Request frame.
針對這個問題，需要考慮測試策略。
4.2.13 需要實現衝突檢測，添加發送消息。LCD是否需要處理？
WM340目前的實現，如果這樣操作，系統會將進入異常流程。需要enhance
4.3
4.4
4.4.1 Protocol extensibility with STA
對於STA WPS IE中還有的特殊字段，比如WPS2.0中爲定義的字段，應該如何處理。
未完待續。
