http://handhelds.org/moin/moin.cgi/SupportedHandheldSummary
Bootloader Messages on the iPAQ hx2750
Soft Reset
Soft Reset = Press reset button on base of device with stylus
*******Beginning System Initialization******* Run Mode = 208 MHz Turbo Mode = Run Mode MemClk = 104 MHz Bus Mode = NORMAL SDCLK[1] = MemClk/2 (SDRAM Clk) SDCLK[0] = MemClk/4 (Sync. FLASH Clk) Mode = RUN Boot FLASH in Asynchronous mode Got Soft Reset
Hard Reset
Hold down the left and right buttons whilst pressing reset button (as described in the manual)
*******Beginning System Initialization******* Run Mode = 208 MHz Turbo Mode = Run Mode MemClk = 104 MHz Bus Mode = NORMAL SDCLK[1] = MemClk/2 (SDRAM Clk) SDCLK[0] = MemClk/4 (Sync. FLASH Clk) Mode = RUN Boot FLASH in Asynchronous mode Got Hard Reset Beginning SDRAM Scrub... SDRAM Scrub Complete
Pre Boot Loader
Hold down the left, second from left and right and second from right buttons whilst pressing reset button
*******Beginning System Initialization******* Run Mode = 208 MHz Turbo Mode = Run Mode MemClk = 104 MHz Bus Mode = NORMAL SDCLK[1] = MemClk/2 (SDRAM Clk) SDCLK[0] = MemClk/4 (Sync. FLASH Clk) Mode = RUN Boot FLASH in Asynchronous mode Got Soft Reset ****************************************************** ****************************************************** ****************************************************** ****************************************************** ****************************************************** OEMInitDebugSerial using UART1 THIS IS PRE BOOT LOADER VERSION PROTO 0.1 Nov 12 2004 13:45:15 Copyright (c) 2002 Microsoft Corporation Portions copyright (c) 2004 LGE Corporation UNKnown SKUs 0x0 HWCONFG SKU C CONFIG CHK: WLAN YES 1 CONFIG CHK: BT YES 1 CONFIG CHK: M-DOC YES 1 CONFIG CHK: BIO YES 1 Flash type L30 Resetting factory default configuration ... Pre Boot Loader Configuration: 0) IP address: 192.168.0.2 1) Subnet mask: 255.255.0.0 2) Boot delay: 5 seconds 3) Reset to factory default configuration C) CTO Configuration Update D) ROM Image Download Now.. E) Normal EBOOT Download Now.. U) USB Downloader P) Pre EBOOT Update.. R) CTO Value Reading
Results of some Commands:
Enter your selection: d Failed to detect and initialize Ethernet controller. Eboot has halted. Enter your selection: c Failed to detect and initialize Ethernet controller. Eboot has halted. Enter your selection: r Board Revision : 0x1 Board ID : 0x3 Product ID : 0x2 0x7 Model ID : 0x4D 0x33 0x0 CPU Type : 0x3 WLAN Present : 0x1 BT Present : 0x1 NAND Present : 0x1 IrDA Present : 0x1 Fingure Present : 0x1 Record Support : 0x1 Enter your selection: e Failed to detect and initialize Ethernet controller. Eboot has halted. Enter your selection: p Enter the Password Pressing asdfgfhjklasdfghjkl <return> E as the password gives: Is that correct Pre-Eboot Image? Type OK or NO typing OK results in: NOW PRE-EBOOT UPDATE START... Failed to detect and initalize Ethernet Controller. Eboot has halted.
Boot Loader
Hold down the left, second from left and second from right buttons whilst pressing reset button
*******Beginning System Initialization******* Run Mode = 208 MHz Turbo Mode = Run Mode MemClk = 104 MHz Bus Mode = NORMAL SDCLK[1] = MemClk/2 (SDRAM Clk) SDCLK[0] = MemClk/4 (Sync. FLASH Clk) Mode = RUN Boot FLASH in Asynchronous mode Got Hard Reset Beginning SDRAM Scrub... SDRAM Scrub Complete ****************************************************** ****************************************************** ****************************************************** ****************************************************** ****************************************************** OEMInitDebugSerial using UART1 Microsoft Windows CE Ethernet Bootloader built Nov 20 2004 10:50:47 Copyright (c) 2002 Microsoft Corporation Portions copyright (c) 2004 LGE Corporation SDRAM SIZE IS 128mb SKU C 0xC000000 HWCONFG SKU C CONFIG CHK: WLAN YES 1 CONFIG CHK: BT YES 1 CONFIG CHK: M-DOC YES 1 CONFIG CHK: BIO YES 1 Flash type L30 Resetting factory default configuration ... Ethernet Boot Loader Configuration: 0) IP address: 192.168.0.2 1) Subnet mask: 255.255.0.0 2) # bootme's: 25 3) Boot delay: 5 seconds 4) DHCP: Disabled 5) Reset to factory default configuration 6) Program SMSC MAC address B) Bluetooth Test Support D) Download image now E) EBoot Update via Ethernet L) Launch existing flash resident image now U) USB Downloader T) CTO H/W Config read Test R) ROM Update
Results of some commands:
Enter your selection: u Connect USB with Host ARS Enter your selection: t H/W Config check: 0x1 H/W Config check: 0x3 H/W Config check: 0x2 H/W Config check: 0x7 H/W Config check: 0x4D H/W Config check: 0x33 H/W Config check: 0x0 H/W Config check: 0x3 H/W Config check: 0x1 H/W Config check: 0x1 H/W Config check: 0x1 H/W Config check: 0x1 H/W Config check: 0x1 H/W Config check: 0x1 Enter your selection: e Failed to detect and initialize Ethernet controller. Eboot has halted. Start EBOOT Mode Enter Enter your selection: Image Downloading Ready Failed to detect and initialize Ethernet controller. Eboot has halted. Enter your selection: b Exit Serial terminal and Test or Write Bluetooth Enter your selection: d Failed to detect and initialize Ethernet controller. NOTE: Onboard LAN91C111 Ethernet controller is not currently supported. Eboot has halted. Enter your selection: r Failed to detect and initialize Ethernet controller. Eboot has halted.