网上淘到一台watchguard的SSL100，旧设备很少人用，网上资料也少。没有密码，且不像一般设备在进入恢复模式后就自动清密码（SSL560 和SSL1000就是如此），进入初始化。只好找到原厂资料，设置成功，记录如下：
节出自v3_1_WG_SSL_WebUI_UserGuide.pdf
web-update—you have the ID &password
下节适用于已知用户名和密码
To install the SSLVPN 3.2 software on your SSLVPN appliance:
- Download the “WgsslOSv3_2.zip” file. Save it to your desktop. Unzip the file.
- Connect to the SSLVPN Web UI Manage System > Device Update page
- Click Browse and navigate to the “stm-sslvpn_tacoma.sysa-dl” file; click Open
- Click Update.
- The appliance automatically reboots when update is complete.
- After reboot, the Web UI Monitor System > System Status page shows version 3.2
下节适用于不知用户名和密码
简单来说就是设置为recovery模式（液晶面板的向上键+power on 或115200－com口进入在进系统之前可选择SYSB状态）
此时eth1的IP变为10.0.1.1,通过ftp更新fireware，将原来的覆盖掉（用户名和密码admin/admin）.这样就恢复成出厂模式，再通过(eth1默认改为192.168.111.1)https://192.168.111.1:8443来配置即可
Before you begin Before you start the recovery process, you must download and save a copy of the WatchGuard SSL OS on your
computer. The file has an extension of .sysa- dl . You can download the file from the Software Downloads section of the WatchGuard web site at http://www.watchguard.com/archive/softwarecenter.asp. Start the WatchGuard SSL device in recovery mode
- Power off the WatchGuard SSL device.
- Press and hold the up arrow button on the front panel while you power on the device.
- Continue to hold the up arrow button until Executing SysB appears on the LCD display. When Recovery Mode Ready appears on
the LCD display, the device is in recovery mode. In recovery mode, the Eth1 address ofthe device is set to 10.0.1.1.
Upload a new software image
You must use a command line FTP program to upload the WatchGuard SSL OS software image. Many common FTP commands are disabled on the WatchGuard SSL device for securityreasons. For example, you cannot change directories (cd) or show the remote working directory (pwd). Other FTP programs rely on these commands to show you alist of files in the remote directory, and do not operate correctly when these commands are disabled. To upload a new software image to your WatchGuard SSL device:
- Connect an Ethernet network cable between your computer and the Eth1 interface on the WatchGuard SSL device.
- Change the IP address of your computer to 10.0.1.2 (or to another IP address on the 10.0.1.0 network).
- Open the command line interface of your computer. For example, select All Programs > Accessories > Command Prompt from the Windows Start Menu if you use Windows XP.
- Change your working directory to the location where you saved the .sysa_ dl file.
- At the command prompt, type ftp 10.0.1.1 to connect to your WatchGuard SSL.
- When requested, type admin for both the user and the password.
- Type bin to change the transfer type to binary mode.
- Type put . Make sure you replace in the command with the name of the .sysa- dl file you downloaded from the WatchGuard Software Downloads page. The upload process can take several minutes to complete. Do not close the window or type more commands until another command prompt appears.
9.Type quit to close the FTP connection. - Exit the command line interface program.
After the software image upload completes, the WatchGuard SSL device installs the software and resets the configuration to the default settings. When the reset process completes, the device automatically restarts. Note The installation and reset process can take up to 10 minutes. Do not turn off the device before this process is complete. Next steps After you restore the software image and the device restarts with factory default settings, you canuse the Quick Setup Wizard to set up your configuration again. Note After the reboot, the IP address of the Eth1 interface changes to 192.168.111.1. You must change the IP address on your computer before you launch the Quick Setup Wizard.
For more information, see Use the Quick Setup Wizard to Set Up a Basic Configuration