思科交換機命令大全

1.設置主機名/系統名

IOS:switch(config)# hostname "hostname"

CLI:switch(enable) set system name name-string

2.設置登錄口令

 IOS:switch(config)# enable password level 1 password

CLI:switch(enable) set password

switch(enable) set enalbepass

3.設置遠程訪問

 IOS:switch(config)# interface vlan 1

switch(config-if)# ip address ip-address netmask

switch(config-if)# ip default-gateway ip-address

CLI:switch(enable) set interface sc0 ip-address netmask broadcast-address

switch(enable) set interface sc0 vlan

switch(enable) set ip route default gateway

4.啓用和瀏覽CDP信息

IOS:switch(config-if)# cdp enable

switch(config-if)# no cdp enable

CLI:switch(enable) set cdp {enable|disable} module/port

5.查看Cisco鄰接設備的CDP通告

IOS:switch#  show cdp interface [type modle/port]

switch#  show cdp neighbors [type module/port] [detail]

CLI:switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]

6.端口描述 IOS:switch(config-if)#description escription-string

CLI:switch(enable)set port name module/number description-string

7.設置端口速度

IOS:switch(config-if)# speed{10|100|auto}

CLI:switch(enable) set port speed moudle/number {10|100|auto}

switch(enable) set port speed moudle/number {4|16|auto}

8.設置以太網的鏈路模式

IOS:switch(config-if)# duplex {auto|full|half}

CLI:switch(enable) set port duplex module/number {full|half}

9.配置靜態VLAN

IOS:switch# vlan database

switch(vlan)# vlan vlan-num name vla

switch(vlan)# exit

switch# configure teriminal

switch(config)#interface interface module/number

switch(config-if)# switchport mode access

switch(config-if)# switchport access vlan vlan-num

switch(config-if)# end

CLI:switch(enable) set vlan vlan-num [name name]

switch(enable) set vlan vlan-num mod-num/port-list

10.配置VLAN中繼線

IOS:switch(config)# interface interface mod/port

switch(config-if)# switchport mode trunk

switch(config-if)#switchport trunk encapsulation {isl|dotlq}

switch(config-if)# switchport trunk allowed vlan remove vlan-list

switch(config-if)# switchport trunk allowed vlan add vlan-list

CLI:switch(enable)set trunk module/port [on|off|desirable|auto|nonegotiate]

Vlan-range [isl|dotlq|dotl0|lane|negotiate]

11.配置VTP管理域

IOS:switch# vlan database

switch(vlan)# vtp domain domain-name

CLI:switch(enable) set vtp [domain domain-name]

12.配置VTP 模式

IOS:switch# vlan database

switch(vlan)# vtp domain domain-name

switch(vlan)# vtp {sever|cilent|transparent}

switch(vlan)# vtp password password

CLI:switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]

13.配置VTP版本

IOS:switch# vlan database

switch(vlan)# vtp v2-mode

CLI:switch(enable) set vtp v2 enable

14.啓動VTP剪裁

IOS:switch# vlan database

switch(vlan)# vtp pruning

CLI:switch(enable) set vtp pruning enable

15.配置以太信道

IOS:switch(config-if)# port group group-number [distribution {source|destination}]

CLI:switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}

16.調整根路徑成本

IOS:switch(config-if)#spanning-tree [vlan vlan-list] cost cost

CLI:switch(enable)set spantree portcost moudle/port cost

switch(enable)set spantree portvlancost moudle/port [cost cost][vlan-list]

17.調整端口ID

IOS:switch(config-if)#spanning-tree[vlan vlan-list]port-priority port-priority

CLI:switch(enable)set spantree portpri {mldule/port}priority

switch(enable)set spantree portvlanpri {module/port}priority [vlans]

18.修改STP時鐘

 IOS:switch(config)# spanning-tree [vlan vlan-list] hello-time seconds

switch(config)#spanning-tree [vlan vlan-list] forward-time seconds

switch(config)#spanning-tree [vlan vlan-list] max-age seconds

CLI:switch(enable) set spantree hello interval[vlan]

switch(enable) set spantree fwddelay delay [vlan]

switch(enable) set spantree maxage agingtiame[vlan]

19.啓用或禁用Port Fast 特徵

IOS:switch(config-if)#spanning-tree portfast

CLI:switch(enable)set spantree portfast {module/port}{enable|disable}

 

20.啓用或禁用UplinkFast 特徵

IOS:switch(config)#spanning-tree uplinkfast [max-update-rate pkts-per-second]

CLI:switch(enable)set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]

爲了將交換機配置成一個集羣的命令交換機,首先要給管理接口分配一個IP地址,然後使用下列命令:

switch(config)# cluster enable cluster-name

21. 爲了從一條中繼鏈路上刪除VLAN,可使用下列命令:

switch(enable) clear trunk module/port vlan-range

22. 用show vtp domain 顯示管理域的VTP參數.

23. 用show vtp statistics顯示管理域的VTP參數.

24. 在Catalyst交換機上定義TrBRF的命令如下:

switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]

25. 在Catalyst交換機上定義TrCRF的命令如下:

switch (enable) set vlan vlan-num [name name] type trcrf {ring hex-ring-num|decring decimal-ring-num} parent vlan-num

26. 在創建好TrBRF VLAN之後,就可以給它分配交換機端口.對於以太網交換,可以採用如下命令給VLAN分配端口:

switch(enable) set vlan vlan-num mod-num/port-num

27. 命令show spantree顯示一個交換機端口的STP狀態.

28. 配置一個ELAN的LES和BUS,可以使用下列命令:

 ATM (config)# interface atm number.subint multioint

ATM(config-subif)# lane serber-bus ethernet elan-name

29. 配置LECS:

ATM(config)# lane database database-name

ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address

ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address

ATM(lane-config-databade)# name ...

30. 創建完數據庫後,必須在主接口上啓動LECS.命令如下: ATM(config)# interface atm number

ATM(config-if)# lane config database database-name

ATM(config-if)# lane config auto-config-atm-address

31. 將每個LEC配置到一個不同的ATM子接口上.命令如下:

ATM(config)# interface atm number.subint multipoint

ATM(config)# lane client ethernet vlan-num elan-num

32. 用show lane server 顯示LES的狀態.

33. 用show lane bus顯示bus的狀態.

34. 用show lane database顯示LECS數據庫可內容.

35. 用show lane client顯示LEC的狀態.

36. 用show module顯示已安裝的模塊列表.

37. 用物理接口建立與VLAN的連接:

router# configure terminal

router(config)# interface media module/port

router(config-if)# description description-string

router(config-if)# ip address ip-addr subnet-mask

router(config-if)# no shutdown

38. 用中繼鏈路來建立與VLAN的連接:

router(config)# interface module/port.subinterface

router(config-ig)# encapsulation[isl|dotlq] vlan-number

router(config-if)# ip address ip-address subnet-mask

39. 用LANE 來建立與VLAN的連接:

router(config)# interface atm module/port

router(config-if)# no ip address

router(config-if)# atm pvc 1 0 5 qsaal

router(config-if)# atm pvc 2 0 16 ilni

router(config-if)# interface atm module/port.subinterface multipoint

router(config-if)# ip address ip-address subnet-mask

router(config-if)# lane client ethernet elan-num

router(config-if)# interface atm module/port.subinterface multipoint

router(config-if)# ip address ip-address subnet-name

router(config-if)# lane client ethernet elan-name

router(config-if)# ...

40. 爲了在路由處理器上進行動態路由配置,可以用下列IOS命令來進行:

router(config)# ip routing

router(config)# router ip-routing-protocol

router(config-router)# network ip-network-number

router(config-router)# network ip-network-number

41. 配置默認路由: switch(enable) set ip route default gateway

42. 爲一個路由處理器分配VLANID,可在接口模式下使用下列命令:

router(config)# interface interface number

router(config-if)# mls rp vlan-id vlan-id-num

43. 在路由處理器啓用MLSP: router(config)# mls rp ip

44. 爲了把一個外置的路由處理器接口和交換機安置在同一個VTP域中:

router(config)# interface interface number

router(config-if)# mls rp vtp-domain domain-name

45. 查看指定的VTP域的信息: router# show mls rp vtp-domain vtp domain name

46. 要確定RSM或路由器上的管理接口,可以在接口模式下輸入下列命令:

router(config-if)#mls rp management-interface

47. 要檢驗MLS-RP的配置情況: router# show mls rp

48. 檢驗特定接口上的MLS配置:router# show mls rp interface interface number

49. 爲了在MLS-SE上設置流掩碼而又不想在任一個路由處理器接口上設置訪問列表:

set mls flow [destination|destination-source|full]

50. 爲使MLS和輸入訪問列表可以兼容,可以在全局模式下使用下列命令:

router(config)# mls rp ip input-acl

51. 當某個交換機的第3層交換失效時,可在交換機的特權模式下輸入下列命令:

switch(enable) set mls enable

52. 若想改變老化時間的值,可在特權模式下輸入以下命令:

switch(enable) set mls agingtime agingtime

53. 設置快速老化:switch(enable) set mls agingtime fast fastagingtime pkt_threshold

54. 確定那些MLS-RP和MLS-SE參與了MLS,可先顯示交換機引用列表中的內容再確定:

switch(enable) show mls include

55. 顯示MLS高速緩存記錄: switch(enable) show mls entry

56. 用命令show in arp顯示ARP高速緩存區的內容。

57. 要把路由器配置爲HSRP備份組的成員,可以在接口配置模式下使用下面的命令:

router(config-if)# standby group-number ip ip-address

58. 爲了使一個路由器重新恢復轉發路由器的角色,在接口配置模式下:

router(config-if)# standy group-number preempt

59. 訪問時間和保持時間參數是可配置的:

router(config-if)# standy group-number timers hellotime holdtime

60. 配置HSRP跟蹤:router(config-if)# standy group-number track type-number interface-priority

61. 要顯示HSRP路由器的狀態:router# show standby type-number group brief

62. 用命令show ip igmp確定當選的查詢器。

63. 啓動IP組播路由選擇:router(config)# ip muticast-routing

64. 啓動接口上的PIM: dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}

65. 啓動稀疏-稠密模式下的PIM:

router# ip multicast-routing

router# interface type number

router# ip pim sparse-dense-mode

66. 覈實PIM的配置: dallasr1># show ip pim interface[type number] [count]

67. 顯示PIM鄰居: dallasr1># show ip neighbor type number

68. 爲了配置RP的地址,命令如下:

dallasr1># ip pim rp-address ip-address [group-access-list-number][override]

69. 選擇一個默認的RP: dallasr1># ip pim rp-address

通告RP和它所服務的組範圍:

dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number

爲管理範圍組通告RP的地址:

dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1

dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255

設定一個RP映像代理:dallasr1># ip pim send-rp-discovery scope ttl

覈實組到RP的映像:

dallasr1># show ip pim rp mapping

dallasr1># show ip pim rp [group-name|group-address] [mapping]

70. 在路由器接口上用命令ip multicast ttl-threshold ttl-value設定TTL閥值:

dallasr1>(config-if)# ip multicast ttl-threshold ttl-value

71. 用show ip pim neighbor顯示PIM鄰居表。

72. 顯示組播通信路由表中的各條記錄:

dallasr1>show ip mroute [group-name|group-address][scoure][summary][count][active kbps]

73. 要記錄一個路由器接受和發送的全部IP組播包:

dallasr1> #debug ip mpacket [detail] [access-list][group]

74. 要在CISCO路由器上配置CGMP: dallasr1>(config-if)# ip cgmp

75.配置一個組播路由器,使之加入某一個特定的組播組:

dallasr1>(config-if)# ip igmp join-group group-address

76. 關閉 CGMP: dallasr1>(config-if)# no ip cgmp

77. 啓動交換機上的CGMP: dallasr1>(enable) set cgmp enable

78. 覈實Catalyst交換機上CGMP的配置情況:

catalystla1>(enable) show config

set prompt catalystla1>

set interface sc0 192.168.1.1 255.255.255.0

set cgmp enable

79. CGMP離開的設置: Dallas_SW(enable) set cgmp leave

80. 在Cisco設備上修改控制端口密碼:

R1(config)# line console 0

R1(config-line)# login

R1(config-line)# password Lisbon

R1(config)# enable password Lilbao

R1(config)# login local

R1(config)# username student password cisco

81. 在Cisco設備上設置控制檯及vty端口的會話超時:

R1(config)# line console 0

R1(config-line)# exec-timeout 5 10

R1(config)# line vty 0 4

R1(config-line)# exec-timeout 5 2

82. 在Cisco設備上設定特權級:

R1(config)# privilege configure level 3 username

R1(config)# privilege configure level 3 copy run start

R1(config)# privilege configure level 3 ping

R1(config)# privilege configure level 3 show run

R1(config)# enable secret level 3 cisco

83. 使用命令privilege 可定義在該特權級下使用的命令:

router(config)# privilege mode level level command

84. 設定用戶特權級:

router(config)# enable secret level 3 dallas

router(config)# enable secret san-fran

router(config)# username student password cisco

85. 標誌設置與顯示:

R1(config)# banner motd ‘unauthorized access will be prosecuted!'

86. 設置vty訪問:

R1(config)# access-list 1 permit 192.168.2.5

R1(config)# line vty 0 4

R1(config)# access-class 1 in

87. 配置HTTP訪問:

Router3(config)# access-list 1 permit 192.168.10.7

Router3(config)# ip http sever

Router3(config)# ip http access-class 1

Router3(config)# ip http authentication local

Router3(config)# username student password cisco

88. 要啓用HTTP訪問,請鍵入以下命令: switch(config)# ip http sever

89. 在基於set命令的交換機上用setCL1啓動和核實端口安全:

switch(enable) set port security mod_num/port_num...enable mac address

switch(enable) show port mod_num/port_num

在基於CiscoIOS命令的交換機上啓動和核實端口安全:

switch(config-if)# port secure [mac-mac-count maximum-MAC-count]

switch# show mac-address-table security [type module/port]

90. 用命令access-list在標準通信量過濾表中創建一條記錄:

Router(config)# access-list access-list-number {permit|deny} source-address [source-address]

91. 用命令access-list在擴展通信量過濾表中創建一條記錄:

Router(config)#access-list access-list-number {permit|deny{protocol|protocol-keyword}}{source source-wildcard|any}{destination destination-wildcard|any}[protocol-specific options][log]

92. 對於帶內路由更新,配置路由更新的最基本的命令格式是:

R1(config-router)#distribute-list access-list-number|name in [type number]

93. 對於帶外路由更新,配置路由更新的最基本的命令格式是:

R1(config-router)#distribute-list access-list-number|name out [interface-name] routing-process| autonomous-system-number

94. set snmp命令選項:

 set snmp community {read-only|ready-write|read-write-all}[community_string]

95. set snmp trap 命令格式如下:

set snmp trap {enable|disable} [all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx]

set snmp trap rvcr_addr rcvr_community

96. 啓用SNMP chassis 陷阱: Console>(enable) set snmp trap enable chassis

97. 啓用所有SNMP chassis 陷阱: Console>(enable) set snmp trap enable

98. 禁用SNMP chassis 陷阱: Console>(enable) set snmp trap disable chassis

99. 給SNMP陷阱接收表加一條記錄: Console>(enable) set snmp trap 192.122.173.42 public

100. show snmp 輸出結果。

101. 命令set snmp rmon enable 的輸出結果。

102. 顯示SPAN信息:Consile> show span

發表評論
所有評論
還沒有人評論,想成為第一個評論的人麼? 請在上方評論欄輸入並且點擊發布.
相關文章