配置ospf验证，汇总，虚链路

配置ospf验证，汇总，虚链路

环境：三台路由器串口相连，其它接口配置如图
要求：1.在area 1配置ospf虚链路,router-id如图配置
2.将R1的LOOP口配置ospf手工路由汇总
3. 配置ospf接口验证（R1 和R2）
4.使用show命令查看结果
 

步骤一： 配置三个路由器接口使其连通。

R1的配置
R1(config)# interface Loopback0
R1(config-if)# ip address 30.1.1.1 255.255.255.0
R1(config)# interface Loopback1
R1(config-if)# ip address 30.1.2.1 255.255.255.0
R1(config)# interface Loopback2
R1(config-if)# ip address 30.1.3.1 255.255.255.0
R1(config)# interface s0
R1(config-if)# ip address 10.1.1.1 255.255.255.0
R1(config-if)#no shutdown

R2的配置
R2(config)# interface Loopback0
R2(config-if)# ip address 50.1.1.1 255.255.255.0
R2(config)# interface s0
R2(config-if)# ip address 10.1.1.2 255.255.255.0
R2(config-if)#clockrate 64000
R2(config-if)#no shutdown
R2(config)# interface s1
R2(config-if)# ip address 20.1.1.1 255.255.255.0
R2(config-if)#no shutdown

R3的配置
R3(config)# interface Loopback0
R3(config-if)# ip address 40.1.1.1 255.255.255.0
R3(config)# interface s1
R3(config-if)# ip address 20.1.1.2 255.255.255.0
R3(config-if)#clockrate 64000
R3(config)#no shutdown

步骤二： 配置ospf

R1的配置
R1(config)#router ospf 1  à启用ospf协议，进程号为1
R1(config-router)#router-id 1.1.1.1  à配置router-id
R1(config-router)#network 10.1.1.0 0.0.0.255 area 1  à将接口参与到区域1内
R1(config-router)#network 30.1.1.0 0.0.0.255 area 0  à将接口参与到区域0内
R1(config-router)#network 30.1.2.0 0.0.0.255 area 0
R1(config-router)#network 30.1.3.0 0.0.0.255 area 0

R2的配置
R2(config)#router ospf 1
R2(config-router)#router-id 2.2.2.2
R2(config-router)#network 10.1.1.0 0.0.0.255 area 1
R2(config-router)#network 20.1.1.0 0.0.0.255 area 2  à将接口参与到区域2内
R2(config-router)#network 50.1.1.0 0.0.0.255 area 1

R3的配置
R3(config)#router ospf 2
R3(config-router)#router-id 3.3.3.3
R3(config-router)#network 20.1.1.0 0.0.0.255 area 2
R3(config-router)#network 40.1.1.0 0.0.0.255 area 2

步骤三：配置ospf虚链路

R1的配置
R1(config)#router ospf 1
R1(config-router)# area 1 virtual-link 2.2.2.2 à配置虚电路,指对端的router-id

R2的配置
R2(config)#router ospf 1
R2(config-router)# area 1 virtual-link 1.1.1.1

步骤四：配置ospf手工路由汇总

R1的配置
R1(config)#router ospf 1
R1(config-router)# area 0 range 30.1.0.0 255.255.252.0  à手工汇总路由

R2的配置
R2(config)#router ospf 1
R2(config-router)# area 0 range 30.1.0.0 255.255.252.0  à因你的区域0已经延伸到此

步骤五：配置ospf接口验证（R1 和R2）

R1的配置
R1(config)# interface Serial0
R1(config-if)# ip ospf authentication message-digest  à启用验证
R1(config-if)# ip ospf message-digest-key 1 md5 cisco à定义密钥

R2的配置
R2(config)# interface Serial0
R2(config-if)# ip ospf authentication message-digest
R2(config-if)# ip ospf message-digest-key 1 md5 cisco  à两端必须一致

步骤六：查看路由表

R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     50.0.0.0/32 is subnetted, 1 subnets
O       50.1.1.1 [110/65] via 10.1.1.2, 00:09:41, Serial0  àOSPF域内学来的路由条目
     20.0.0.0/24 is subnetted, 1 subnets
O IA    20.1.1.0 [110/128] via 10.1.1.2, 00:09:31, Serial0  àOSPF域间学来的路由条目
     40.0.0.0/32 is subnetted, 1 subnets
O IA    40.1.1.1 [110/129] via 10.1.1.2, 00:09:31, Serial0
     10.0.0.0/24 is subnetted, 1 subnets
C       10.1.1.0 is directly connected, Serial0
     30.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
C       30.1.3.0/24 is directly connected, Loopback2
C       30.1.2.0/24 is directly connected, Loopback1
C       30.1.1.0/24 is directly connected, Loopback0
O       30.1.0.0/22 is a summary, 00:09:32, Null0  à手工汇总的条目

R2#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     50.0.0.0/24 is subnetted, 1 subnets
C       50.1.1.0 is directly connected, Loopback0
     20.0.0.0/24 is subnetted, 1 subnets
C       20.1.1.0 is directly connected, Serial1
     40.0.0.0/32 is subnetted, 1 subnets
O       40.1.1.1 [110/65] via 20.1.1.2, 00:04:48, Serial1
     10.0.0.0/24 is subnetted, 1 subnets
C       10.1.1.0 is directly connected, Serial0
     30.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
O       30.1.2.1/32 [110/65] via 10.1.1.1, 00:04:38, Serial0
O       30.1.3.1/32 [110/65] via 10.1.1.1, 00:04:39, Serial0
O       30.1.0.0/22 is a summary, 00:04:39, Null0
O       30.1.1.1/32 [110/65] via 10.1.1.1, 00:04:39, Serial0

R3#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     50.0.0.0/32 is subnetted, 1 subnets
O IA    50.1.1.1 [110/65] via 20.1.1.1, 00:02:02, Serial1
     20.0.0.0/24 is subnetted, 1 subnets
C       20.1.1.0 is directly connected, Serial1
     40.0.0.0/24 is subnetted, 1 subnets
C       40.1.1.0 is directly connected, Loopback0
     10.0.0.0/24 is subnetted, 1 subnets
O IA    10.1.1.0 [110/128] via 20.1.1.1, 00:02:02, Serial1
     30.0.0.0/22 is subnetted, 1 subnets
O IA    30.1.0.0 [110/129] via 20.1.1.1, 00:01:47, Serial1

步骤七：查看邻居表

R1#show ip ospf neighbor  à邻居已建立，点对点无DR之说

Neighbor ID     Pri   State           Dead Time   Address         Interface
2.2.2.2           1   FULL/  -        00:00:33    10.1.1.2        Serial0

R2#show ip ospf neighbor

Neighbor ID     Pri   State           Dead Time   Address         Interface
1.1.1.1           1   FULL/  -        00:00:33    10.1.1.1        Serial0
3.3.3.3           1   FULL/  -        00:00:34    20.1.1.2        Serial1

R3#show ip ospf neighbor

Neighbor ID     Pri   State           Dead Time   Address         Interface
2.2.2.2           1   FULL/  -        00:00:37    20.1.1.1        Serial1

步骤八：用ping命令测试

R1#ping 40.1.1.1 à测试连通性
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/60/68 ms

R1#ping 50.1.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/36 ms

R2#ping 30.1.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms

 

步骤九：显示当前配置信息

R1的配置信息
R1#sh run
hostname R1
!
interface Loopback0
 ip address 30.1.1.1 255.255.255.0
!
interface Loopback1
 ip address 30.1.2.1 255.255.255.0
!
interface Loopback2
 ip address 30.1.3.1 255.255.255.0
!
interface Serial0
 ip address 10.1.1.1 255.255.255.0
 ip ospf authentication message-digest
 ip ospf message-digest-key 1 md5 cisco
!
router ospf 1
 router-id 1.1.1.1
area 0 range 30.1.0.0 255.255.252.0
 area 1 virtual-link 2.2.2.2
 network 10.1.1.0 0.0.0.255 area 1
 network 30.1.1.0 0.0.0.255 area 0
 network 30.1.2.0 0.0.0.255 area 0
 network 30.1.3.0 0.0.0.255 area 0
end

R2#sh run
hostname R2
interface Loopback0
 ip address 50.1.1.1 255.255.255.0
!
interface Serial0
 ip address 10.1.1.2 255.255.255.0
 ip ospf authentication message-digest
 ip ospf message-digest-key 1 md5 cisco
 clockrate 64000
!
interface Serial1
 ip address 20.1.1.1 255.255.255.0
!
router ospf 1
 router-id 2.2.2.2
 area 0 range 30.1.0.0 255.255.252.0
 area 1 virtual-link 1.1.1.1
 network 10.1.1.0 0.0.0.255 area 1
 network 20.1.1.0 0.0.0.255 area 2
 network 50.1.1.0 0.0.0.255 area 1
end

R3#sh run
Hostname R3
!
interface Loopback0
 ip address 40.1.1.1 255.255.255.0
!
interface Serial1
 ip address 20.1.1.2 255.255.255.0
 clockrate 64000
!
router ospf 2
 router-id 3.3.3.3
 network 20.1.1.0 0.0.0.255 area 2
 network 40.1.1.0 0.0.0.255 area 2
end