Cisco 2600灌IOS日誌

    rommon 61 > "IP_ADDRESS=10.16.1.2"
　　rommon 62 > "IP_SUBNET_MASK=255.255.255.0"
　　rommon 63 > "DEFAULT_GATEWAY=10.16.1.1"
　　rommon 64 > "TFTP_SERVER=10.16.1.4"
　　rommon 65 > "TFTP_FILE=c2600-i-mz.121-5.T8"
　　rommon 66 > tftpdnld
　　
　　 IP_ADDRESS: 10.16.1.2
　　 IP_SUBNET_MASK: 255.255.255.0
　　 DEFAULT_GATEWAY: 10.16.1.1
　　 TFTP_SERVER: 10.16.1.4
　　 TFTP_FILE: c2600-i-mz.121-5.T8
　　
　　Invoke this command for disaster recovery only.
　　WARNING: all existing data in all partitions on flash will be lost!
　　Do you wish to continue? y/n: [n]: y
　　
　　Receiving c2600-i-mz.121-5.T8 from 10.16.1.4 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
　　!!!!!!!
　　File reception completed.
　　Copying file c2600-i-mz.121-5.T8 to flash.
　　Erasing flash at 0x607c0000
　　program flash location 0x604e0000
　　rommon 67 >
　　rommon 67 >
　　rommon 67 >
　　rommon 67 > boot
　　program load complete, entry point: 0x80008000, size: 0x4e02f0
　　Self decompressing the image : #################################################
　　################################################################################
　　################################################################################
　　################################################################################
　　################################################################################
　　################################################################################
　　################################################################################
　　################################################################################
　　### [OK]
　　
　　Smart Init is enabled
　　smart init is sizing iomem
　　ID MEMORY_REQ TYPE
　　000091 0X00092280 C2600 single Ethernet
　　 0X000F34A8 public buffer pools
　　 0X00211000 public particle pools
　　TOTAL: 0X00396728
　　
　　If any of the above Memory Requirements are
　　"UNKNOWN", you may be using an unsupported
　　configuration or there is a software problem and
　　system operation may be compromised.
　　Rounded IOMEM up to: 4Mb.
　　Using 12 percent iomem. [4Mb/32Mb]
　　
　　 Restricted Rights Legend
　　
　　Use, duplication, or disclosure by the Government is
　　subject to restrictions as set forth in subparagraph
　　(c) of the Commercial Computer Software - Restricted
　　Rights clause at FAR sec. 52.227-19 and subparagraph
　　(c) (1) (ii) of the Rights in Technical Data and Computer
　　Software clause at DFARS sec. 252.227-7013.
　　
　　 cisco Systems, Inc.
　　 170 West Tasman Drive
　　 San Jose, California 95134-1706
　　
　　
　　
　　Cisco Internetwork Operating System Software
　　IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1)
　　TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
　　Copyright (c) 1986-2001 by cisco Systems, Inc.
　　Compiled Mon 07-May-01 17:57 by ccai
　　Image text-base: 0x80008088, data-base: 0x80972320
　　
　　cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory
　　.
　　Processor board ID JAD05090M7A (447016375)
　　M860 processor: part number 0, mask 49
　　Bridging software.
　　X.25 software, Version 3.0.0.
　　1 Ethernet/IEEE 802.3 interface(s)
　　2 Serial network interface(s)
　　32K bytes of non-volatile configuration memory.
　　8192K bytes of processor board System flash (Read/Write)
　　
　　
　　
　　Press RETURN to get started!
　　
　　
　　00:00:12: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
　　00:00:12: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
　　00:00:12: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
　　00:00:13: %SYS-5-CONFIG_I: Configured from memory by console
　　00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
　　tate to up
　　00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta
　　te to down
　　00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed sta
　　te to down
　　00:00:14: %LINK-5-CHANGED: Interface Serial0/1, changed state to administrativel
　　y down
　　00:00:15: %SYS-5-RESTART: System restarted --
　　Cisco Internetwork Operating System Software
　　IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1)
　　TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
　　Copyright (c) 1986-2001 by cisco Systems, Inc.
　　Compiled Mon 07-May-01 17:57 by ccai
　　Cisco2610-003>
　　
　　Cisco2610-003>en