端口概述
Port 1-16 是內聯刀片的downlink口
Port 17-18 是switch互聯用,默認是disable的
Port 19是給Blade On-board Administrator用
Port 20-24 是uplink口
Port 17-18 是switch互聯用,默認是disable的
Port 19是給Blade On-board Administrator用
Port 20-24 是uplink口
連到交換機的Console口
To access the switch locally:
1. Connect the switch DB-9 serial connector, using the null-modem serial cable to a local client device (such as a laptop computer) with VT100 terminal emulation software.
2. Open a VT100 terminal emulation session with these settings: 9600 baud rate, eight data bits, no parity, one stop bit, and no flow control.
初次配置概述
1. 登錄默認密碼:user級別口令: user/user,管理員口令: admin/admin
2. 修改默認口令 cfg → sys → access → user → admpw → apply → save
>> Main# /cfg
>> Configuration# sys
>> System# access/user/admpw
Changing ADMINISTRATOR password; validation required:
Enter current admin password:
Enter new administrator password:
Re-enter new administrator password:
New administrator password accepted.
>> System# apply
>> System# save
>> Configuration# sys
>> System# access/user/admpw
Changing ADMINISTRATOR password; validation required:
Enter current admin password:
Enter new administrator password:
Re-enter new administrator password:
New administrator password accepted.
>> System# apply
>> System# save
千萬記得每次更改完配置,必須用apply纔會生效,爲保證重啓後也繼續生效,一定要save!
網絡配置,21端口上聯到Core 1,22端口上聯到Core 2,所以要添加此端口關聯到所有VLAN,並且在上聯端口上enable tag,所有downlink都不需要tag
配置21和22端口爲tagged
配置命令 cfg → port 22→ ena → cur →tag e →apply → save → cur
配置21和22端口到網管vlan 11
(同樣的配置重複操作,直到把21、22口加入到所有需要加入的vlan)
(同樣的配置重複操作,直到把21、22口加入到所有需要加入的vlan)
配置命令cfg → l2 → vlan 11 → ena →add 21 → add 22 → apply → save → cur
配置管理IP地址
配置命令cfg → l3 → if 1 → addr → mask → ena → apply → save → cur
配置交換機gw
配置命令cfg → l3 → gw 1 → addr → ena →apply → save → cur
默認情況下http和telnet都是enable的,所以根據以上配置完以後,就可以遠程telnet到交換機了,或者通過IE來管理交換機
命令解釋:
cfg -- Configure ,是第一層菜單
sys -- System
l2 -- Layer 2, vlan 配置在這裏做
l3 -- Layer 3, 網管IP, interface配置在這裏
port -- 端口配置
ena -- enable
addr -- 設置地址
mask -- 設置掩碼
cur -- current的縮寫,查看當前配置
apply -- 應用配置(沒apply之前cur顯示的還是舊的)
save --保存配置,這樣reboot後配置不會丟失
命令解釋:
cfg -- Configure ,是第一層菜單
sys -- System
l2 -- Layer 2, vlan 配置在這裏做
l3 -- Layer 3, 網管IP, interface配置在這裏
port -- 端口配置
ena -- enable
addr -- 設置地址
mask -- 設置掩碼
cur -- current的縮寫,查看當前配置
apply -- 應用配置(沒apply之前cur顯示的還是舊的)
save --保存配置,這樣reboot後配置不會丟失
注:默認telnet/console session的保持時間是5分鐘
本文出自 “delxu的Live記事本” 博客,請務必保留此出處http://delxu.blog.51cto.com/975660/240365
本文出自 51CTO.COM技術博客