Cisco路由配置語句彙總
啓動接口,分配IP地址: router> router> enable router# router# configure terminal router(config)# router(config)# interface Type Port router(config-if)# no shutdown router(config-if)# ip address IP-Address Subnet-Mask router(config-if)# ^z 配置RIP路由協議:30秒更新一次 router(config)# router rip router(config-if)# network Network-Number <--通告標準A,B,C類網--> router(config-if)# ^z 配置IGRP路由協議:90秒更新一次 router(config)# router igrp AS-Number <-- AS-Number範圍1~65535--> router(config-if)# network Network-Number <--通告標準A,B,C類網--> router(config-if)# ^z 配置Novell IPX路由協議:Novell RIP 60秒更新一次 router(config)# ipx routing [node address] router(config)# ipx maximum-paths Paths <--設置負載平衡,範圍1~512--> router(config)# interface Type Port router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] <--通告標準A,B,C類網--> router(config-if)# ^z 配置DDR: router(config)# dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number] router(config)# interface bri 0 router(config-if)# dialer-group Group-Number router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number router(config-if)# ^z 配置ISDN: router(config)# isdn swith-type Swith-Type <--配置ISDN交換機類型,中國使用basic-net3--> router(config-if)# ^z 配置Frame Relay: router(config-if)# encapsulation frame-relay [cisco | ietf ] router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ] router(config-if)# bandwidth kilobits router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ] <--配置靜態Invers ARP表: router(config)# frame-relay Protocol Protocol-Address DLCI [ Broadcast ] [ ietf | cisco ] [ payload-compress | packet-by-packet ] --> <--設置Keepalive間隔: router(config-if)# keepalive Number --> <--爲本地接口指定DLCI: router(config-if)# frame-lelay local-dlci Number --> <--子接口配置: router(config-if)# interface Type Port.Subininterface-Number [ multipoint | point-to-point ] router(config-subif)# ip unnumbered Interface router(config-subif)# frame-lelay local-dlci Number --> router(config-if)# ^z 配置標準ACL: router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] <-- Access-List-Number 範圍:1~99標準ACL;100~199擴展ACL;800~899標準IPX ACL;900~999擴展IPX ACL;1000~1099 IPX SAP ACL;600~699Apple Talk ACL--> router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z 配置擴展ACL: router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ] router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z 配置命名ACL: router(config)# ip access-list [ standard | extended ] ACL-Name router(config [ std- | ext- ] nacl)# [ permit | deny ] [ IP-Access-List-Test-Conditions ] router(config [ std- | ext- ] nacl)# no [ permit | deny ] [ IP-Access-List-Test-Conditions ] router(config [ std- | ext- ] nacl)# ^z router(config)# interface Type Port router(config-if)# ip access-group [ACL-Name | 1~199 ] [ in | out ] router(config-if)# ^z 配置DCE時鐘: router# show controllers Type Port <--確定DCE接口--> router(confin-if)# clock rate 64000 <--進入DCE接口設置時鐘速率--> router(config-if)# ^z 配置PPP協議: router(config)# username Name password Set-Password-Here <--驗證方建立數據庫--> router(config)# interface Type Port router(config-if)# encapsulation ppp <--啓動PPP協議--> router(config-if)# ppp outhentication [ chap | chap pap | pap chap | pap ] <--選擇PPP認證--> router(config-if)# ppp pap sent-username Name password Password <--發送驗證信息--> router(config-if)# ^z PAP單向認證配置實例: 驗證方: router-server(config)# username Client password 12345 <--驗證方建立數據庫--> router-server(config)# interface serial 0 router-server(config-if)# encapsulation ppp router-server(config-if)# ppp authentication pap <--選擇使用PAP實現PPP認證--> router-server(config-if)# ^z 被驗證方: router-client(config-if)# encapsulation ppp router-client(config-if)# ppp pap sent-username Client password 12345 <--發送驗證信息--> router-client(config-if)# ^z PAP雙向認證配置實例: 路由器 A: routerA(config)# username B password 12345 routerA(config)# interface serial 0 routerA(config-if)# encapsulation ppp routerA(config-if)# ppp authentication pap routerA(config-if)# ppp pap sent-username A password 54321 routerA(config-if)# ^z 路由器 B: routerB(config)# username A password 54321 routerB(config)# interface serial 1 routerB(config-if)# encapsulation ppp routerB(config-if)# ppp authentication pap routerB(config-if)# ppp pap sent-username B password 12345 routerB(config-if)# ^z CHAP單向認證配置實例: 驗證方: router-server(config)# username router-client password 12345 router-server(config)# interface serial 0 router-server(config-if)# encapsulation ppp router-server(config-if)# ppp authentication chap router-server(config-if)# ^z 被驗證方: router-client(config-if)# encapsulation ppp router-client(config-if)# ppp authentication chap router-client(config-if)# ppp chap hostname router-client router-client(config-if)# ppp chap password 12345 router-client(config-if)# ^z CHAP雙向認證配置實例: 路由器 A: routerA(config)# username routerB password 12345 routerA(config)# interface serial 0 routerA(config-if)# encapsulation ppp routerA(config-if)# ppp authentication chap routerA(config-if)# ppp chap hostname routerA routerA(config-if)# ppp chap password 54321 routerA(config-if)# ^z 路由器 B: routerB(config)# username routerA password 54321 routerB(config)# interface serial 1 routerB(config-if)# encapsulation ppp routerB(config-if)# ppp authentication chap routerB(config-if)# ppp chap hostname routerB routerB(config-if)# ppp chap password 12345 routerB(config-if)# ^z Telnet使用: routerA# terminal monitor <--可以傳回在遠端主機執行Debug命令的結果--> routerA# telnet IP-Address [ Router-Name ] <--Telnet到指定的地址或名字的主機--> routerB# [ exit | logout ] <--退出Telnet--> routerB# ++<6>再按 <--掛起Telnet--> routerA# show sessions <--顯示當前所有Telnet的信息,包括Connect-Number --> routerA# Connect-Number <--返回指定的Telnet連接--> routerA# disconnect IP-Address [ Router-Name ] <--斷開指定地址或名字的主機的連接--> routerA# show user <--顯示Telnet到本機的連接信息--> routerA# clear line [ 0 | 1 | 2 | 3 | 4 ] <--斷開指定Telnet到本機的連接--> 禁止任何Telnet到本機: router(config)# line vty 0 4 router(config-line)# access-class ACL-Number router(config)# ^z 設置主機名: router(config)# hostname Set-Hostname router(config)# ^z router(config)# ^z 設置用戶模式密碼: router(config)# line console 0 router(config-line)# login router(config-line)# password Set-Password router(config-line)# ^z 設置Telnet密碼: router(config)# line vty 0 4 router(config-line)# login router(config-line)# password Set-Password router(config-line)# ^z 設置特權模式密碼: router(config)# enable password Set-Password <--不加密的密碼,明碼--> router(config)# enable secret Set-Password <--經過加密的密碼--> router(config)# ^z 給所有密碼加密: router(config)# service password-ancryption Set-Password-Here router(config)# no service password-ancryption <--取消加密--> router(config)# ^z 設置登錄Banner: router(config)# banner motd 分隔符 Set-Banner-InFORMation-Here 分隔符 <--前後分隔符一定要一致--> 設置接口的描述信息: router(config-if)# description Set-Port-InFORMation-Here router(config)# ^z CDP的控制: router(config-if)# cdp enable <--在指定端口啓用CDP,缺省--> router(config-if)# no cdp enable <--在指定端口關閉CDP--> router(config)# cdp run <--使所有端口啓用CDP--> router(config)# no cdp run <--使所有端口關閉CDP--> Ping的使用: router# ping IP-Address router# ping <--擴展Ping命令--> Protocol [ip]:[ Protocol-Type ] <--選擇協議類型--> Target IP address:IP-Address <--輸入測試地址--> Repeat count [5]: <--選擇發送的ICMP包數量--> Datagram size [100]: <--選擇每個包的大小--> Timeout in seconds [2]: <--設置每個包的超時時間--> Extended commands [n]:y <--使用擴展Ping命令--> Sweep range of sizes [n]: Tracke的使用: router# trace IP-Address [ Host-Name ] 爲Cisco 4000路由器指定媒體類型: router(config-if)# media-type 10baset <--使AUI(默認)失效,改爲使用RJ-45--> router(config-if)# ^z 更改路由器啓動順序: router(config)# boot system flash IOS-FileName router(config)# boot system tftp IOS-FileName TFTP-IP-Address router(config)# boot system rom router(config)# ^z 修改寄存器數值: router(config)# config-register value <--Cisco出廠默認value=0x2102,value範圍:0x2100(進入ROM監視器),0x2101(使系統從ROM啓動),0x2102~0x210F(使系統從NVRAM啓動)。0x1=0x2101,從最小位開始改變--> 在ROM監視器中更改寄存器數值: > o/r value 路由器密碼的恢復: 冷關機,然後再開機並在60秒內按< Ctrl>+進入ROM監視器模式 > o/r 0x2142 <--25xx型路由器--> 或 > confreg 0x2142 <--16xx型路由器--> router> I router> n router> enable router# copy startup-config running-config router# configure terminal router(config)# enable secret New-Password router(config)# config-register 0x2102 router(config)# ^z router# copy running-config startup-config router# reload 配置名稱-主機入口: router(config)# ip host Set-Name [ TCP-Port-Number ] IP-Address [ IP-Address 2 ]... router(config)# ^z 定義DNS主機: router(config)# ip name-server Server-Address [ Server-Address 2 ]... router(config)# ^z 禁用DNS: router(config)# no ip domain-lookup router(config)# ^z 配置水平分割: router(config-if)# ip split-horizon router(config-if)# no ip split-horizon router(config-if)# ^z 配置靜態路由: router(config)# ip route IP-Address Subnet-Mask [ Next-Hop-Address | Local-Out-Port ] [Distace ] <--Distance範圍:1~255,相當於優先權,越小越好。RIP=120;DSPF=110;IGRP=100;EIGRP=90--> router(config)# ^z 配置缺省路由: router(config)# ip defoult-network IP-Address <--動態缺省路由--> router(config)# ip route 0.0.0.0 0.0.0.0 [ Next-Hop-Address | Local-Out-Port ] [Distace ] <--靜態缺省路由--> router(config)# ^z 其它命令: router# show version router# show running-config router# show startup-config router# show flash router# show interface [ Type Port ] router# show buffers router# show protocol router# show mem router# show stacks router# show processes router# show cdp entry [ Device-Name ] <--顯示指定鄰居三層信息--> router# show cdp neighbors router# show cdp neighbors detail <---顯示所有鄰居三層信息-> router# show ip router router# show ipx router router# show host router# show ip protocol router# show ip interface Type Port router# show ipx interface Type Port router# show ipx servers router# show ipx traffic router# show access-lists [ ACL-Number ] router# show isdn status router# show dialer <--查看ISDN撥號信息--> router# show isdn active router# show frame-relay pvc router# show frame-relay map router# show frame-relay lmi router# erase startup-config router# reload router# setup router# copy running-config startup-config router# copy startup-config running-config router# copy tftp running-config router# copy running-config tftp router# debug ipx routing activity router# debug ipx sap router# debug isdn q921 router# debug isdn q931 router# debug dialer router# debug ip rip router# clear interface bri |