1. 交換機 支持的命令:
交換機基本狀態: switch: ;ROM狀態, 路由器是rommon> hostname> ;用戶模式 hostname# ;特權模式 hostname(config)# ;全局配置模式 hostname(config-if)# ;接口狀態 交換機口令設置: switch>enable ;進入特權模式 switch#config terminal ;進入全局配置模式 switch(config)#hostname ;設置交換機的主機名 switch(config)#enable secret xxx ;設置特權加密口令 switch(config)#enable password xxa ;設置特權非密口令 switch(config)#line console 0 ;進入控制檯口 switch(config-line)#line vty 0 4 ;進入虛擬終端 switch(config-line)#login ;允許登錄 switch(config-line)#password xx ;設置登錄口令xx switch#exit ;返回命令 交換機VLAN設置: switch#vlan database ;進入VLAN設置 switch(vlan)#vlan 2 ;建VLAN 2 switch(vlan)#no vlan 2 ;刪vlan 2 switch(config)#int f0/1 ;進入端口1 switch(config-if)#switchport access vlan 2 ;當前端口加入vlan 2 switch(config-if)#switchport mode trunk ;設置爲幹線 switch(config-if)#switchport trunk allowed vlan 1,2 ;設置允許的vlan switch(config-if)#switchport trunk encap dot1q ;設置vlan 中繼 switch(config)#vtp domain ;設置發vtp域名 switch(config)#vtp password ;設置發vtp密碼 switch(config)#vtp mode server ;設置發vtp模式 switch(config)#vtp mode client ;設置發vtp模式 交換機設置IP地址: switch(config)#interface vlan 1 ;進入vlan 1 switch(config-if)#ip address ;設置IP地址 switch(config)#ip default-gateway ;設置默認網關 switch#dir flash: ;查看閃存 交換機顯示命令: switch#write ;保存配置信息 switch#show vtp ;查看vtp配置信息 switch#show run ;查看當前配置信息 switch#show vlan ;查看vlan配置信息 switch#show interface ;查看端口信息 switch#show int f0/0 ;查看指定端口信息 2. 路由器支持的命令: 路由器 顯示 命令: router#show run ;顯示配置信息 router#show interface ;顯示接口信息 router#show ip route ;顯示路由信息 router#show cdp nei ;顯示鄰居信息 router#reload ;重新起動 路由器口令設置: router>enable ;進入特權模式 router#config terminal ;進入全局配置模式 router(config)#hostname ;設置交換機的主機名 router(config)#enable secret xxx ;設置特權加密口令 router(config)#enable password xxb ;設置特權非密口令 router(config)#line console 0 ;進入控制檯口 router(config-line)#line vty 0 4 ;進入虛擬終端 router(config-line)#login ;要求口令驗證 router(config-line)#password xx ;設置登錄口令xx router(config)#(Ctrl+z) ; 返回特權模式 router#exit ;返回命令 路由器 配置 : router(config)#int s0/0 ;進入Serail接口 router(config-if)#no shutdown ;激活當前接口 router(config-if)#clock rate 64000 ;設置同步時鐘 router(config-if)#ip address ;設置IP地址 router(config-if)#ip address second ;設置第二個IP router(config-if)#int f0/0.1 ;進入子接口 router(config-subif.1)#ip address ;設置子接口IP router(config-subif.1)#encapsulation dot1q ;綁定vlan中繼協議 router(config)#config-register 0x2142 ;跳過配置文件 router(config)#config-register 0x2102 ;正常使用配置文件 router#reload ;重新引導 路由器文件操作: router#copy running-config startup-config ;保存配置 router#copy running-config tftp ;保存配置到tftp router#copy startup-config tftp ;開機配置存到tftp router#copy tftp flash: ;下傳文件到flash router#copy tftp startup-config;下載配置文件 ROM狀態: Ctrl+Break ;進入ROM監控狀態 rommon>confreg 0x2142 ;跳過配置文件 rommon>confreg 0x2102 ;恢復配置文件 rommon>reset ;重新引導 rommon>copy xmodem: flash: ;從console傳輸文件 rommon>IP_ADDRESS=10.65.1.2 ;設置 路由器 IP rommon>IP_SUBNET_MASK=255.255.0.0 ;設置路由器掩碼 rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP 服務 器IP rommon>TFTP_FILE=c2600.bin ;指定下載的文件 rommon>tftpdnld ;從tftp下載 rommon>dir flash: ;查看閃存內容 rommon>boot ;引導IOS 靜態路由: ip route ;命令格式 router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;靜態路由舉例 router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默認路由舉例 動態路由: router(config)#ip routing ;啓動路由轉發 router(config)#router rip ;啓動RIP路由協議。 router(config-router)#network ;設置發佈路由 router(config-router)#negihbor ;點對點幀中繼用。 幀中繼命令: router(config)#frame-relay switching ;使能幀中繼交換 router(config-s0)#encapsulation frame-relay ;使能幀中繼 router(config-s0)#fram-relay lmi-type cisco ;設置管理類型 router(config-s0)#frame-relay intf-type DCE ;設置爲DCE router(config-s0)#frame-relay dlci 16 ; router(config-s0)#frame-relay local-dlci 20 ;設置虛電路號 router(config-s0)#frame-relay interface-dlci 16 ; router(config)#log-adjacency-changes ;記錄鄰接變化 router(config)#int s0/0.1 point-to-point ;設置子接口點對點 router#show frame pvc ;顯示永久虛電路 router#show frame map ;顯示映射 基本訪問控制列表: router(config)#access-list permit|deny router(config)#interface ;default:deny any router(config-if)#ip access-group in|out ;default:out 例1: router(config)#access-list 4 permit 10.8.1.1 router(config)#access-list 4 deny 10.8.1.0 0.0.0.255 router(config)#access-list 4 permit 10.8.0.0 0.0.255.255 router(config)#access-list 4 deny 10.0.0.0 0.255.255.255 router(config)#access-list 4 permit any router(config)#int f0/0 router(config-if)#ip access-group 4 in 擴展訪問控制列表: access-list permit|deny icmp wild>[type] access-list permit|deny tcp wild>[port] 例2: router(config)#access-list 101 deny icmp any 10.64.0.2 0.0.0.0 echo router(config)#access-list 101 permit ip any any router(config)#int s0/0 router(config-if)#ip access-group 101 in 例3: router(config)#access-list 102 deny tcp any 10.65.0.2 0.0.0.0 eq 80 router(config)#access-list 102 permit ip any any router(config)#interface s0/1 router(config-if)#ip access-group 102 out 刪除訪問控制例表: router(config)#no access-list 102 router(config-if)#no ip access-group 101 in 路由器 的nat配置 Router(config-if)#ip nat inside ;當前接口指定爲內部接口 Router(config-if)#ip nat outside ;當前接口指定爲外部接口 Router(config)#ip nat inside source static [p] <私有IP><公網IP> [port] Router(config)#ip nat inside source static 10.65.1.2 60.1.1.1 Router(config)#ip nat inside source static tcp 10.65.1.3 80 60.1.1.1 80 Router(config)#ip nat pool p1 60.1.1.1 60.1.1.20 255.255.255.0 Router(config)#ip nat inside source list 1 pool p1 Router(config)#ip nat inside destination list 2 pool p2 Router(config)#ip nat inside source list 2 interface s0/0 overload Router(config)#ip nat pool p2 10.65.1.2 10.65.1.4 255.255.255.0 type rotary Router#show ip nat translation rotary 參數是輪流的意思,地址池中的IP輪流與NAT分配的地址匹配。 overload參數用於PAT 將內部IP映射到一個公網IP不同的端口上。 外部網關協議配置: routerA(config)#router bgp 100 routerA(config-router)#network 19.0.0.0 routerA(config-router)#neighbor 8.1.1.2 remote-as 200 配置PPP驗證: RouterA(config)#username password RouterA(config)#int s0 RouterA(config-if)#ppp authentication {chap|pap} 3. PIX防火牆命令 Pix525(config)#nameif ethernet0 outside security0 ;命名接口和級別 Pix525(config)#interface ethernet0 auto ;設置接口方式 Pix525(config)#interface ethernet1 100full ;設置接口方式 Pix525(config)#interface ethernet1 100full shutdown Pix525(config)#ip address inside 192.168.0.1 255.255.255.0 Pix525(config)#ip address outside 133.0.0.1 255.255.255.252 Pix525(config)#global (if_name) natid ip-ip ;定義公網IP區間 Pix525(config)#global (outside) 1 7.0.0.1-7.0.0.15 ;例句 Pix525(config)#global (outside) 1 133.0.0.1 ;例句 Pix525(config)#no global (outside) 1 133.0.0.1 ;去掉設置 Pix525(config)#nat (if_name) nat_id local_ip [netmark] Pix525(config)#nat (inside) 1 0 0 內網所有主機(0代表0.0.0.0)可以訪問global 1指定的外網。 Pix525(config)#nat (inside) 1 172.16.5.0 255.255.0.0 內網172.16.5.0/16網段的主機可以訪問global 1指定的外網。 Pix525(config)#route if_name 0 0 gateway_ip [metric] ;命令格式 Pix525(config)#route outside 0 0 133.0.0.1 1 ;例句 Pix525(config)#route inside 10.1.0.0 255.255.0.0 10.8.0.1 1 ;例句 Pix525(config)#static (inside, outside) 133.0.0.1 192.168.0.8 表示內部ip地址192.168.0.8,訪問外部時被翻譯成133.0.0.1全局地址。 Pix525(config)#static (dmz, outside) 133.0.0.1 172.16.0.8 中間區域ip地址172.16.0.8,訪問外部時被翻譯成133.0.0.1全局地址。 |
Cisco路由器交換機配置命令詳解
發表評論
所有評論
還沒有人評論,想成為第一個評論的人麼? 請在上方評論欄輸入並且點擊發布.