Branch3(config-subif)#encapsulation dot1Q vl
Branch3(config-subif)#encapsulation dot1Q ?
<1-4094> IEEE 802.1Q VLAN ID
Branch3(config-subif)#encapsulation dot1Q 10
Branch3(config-subif)#exit
Branch3(config)#int
Branch3(config)#interface g
Branch3(config)#interface gigabitEthernet 0/0.20
Branch3(config-subif)#enc
Branch3(config-subif)#encapsulation d
Branch3(config-subif)#encapsulation dot1Q 20
Branch3(config-subif)#exit
Branch3(config)#do show int bri
Branch3(config)#do show int bri
show int bri
^
% Invalid input detected at '^' marker.
Branch3(config)#do show ip int bri
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 unassigned YES unset up up
GigabitEthernet0/0.10 unassigned YES unset up up
GigabitEthernet0/0.20 unassigned YES unset up up
GigabitEthernet0/0.30 192.168.1.193 YES manual up up
GigabitEthernet0/0.88 192.168.1.225 YES manual up up
GigabitEthernet0/0.99 192.168.1.241 YES manual up up
GigabitEthernet0/1 192.168.0.1 YES manual up up
Serial0/0/0 192.168.3.250 YES manual up up
Serial0/0/1 192.168.3.242 YES manual up up
Vlan1 unassigned YES unset administratively down down
Branch3(config)#int
Branch3(config)#interface g
Branch3(config)#interface gigabitEthernet 0/0.10
Branch3(config-subif)#ip add
Branch3(config-subif)#ip address 192.168.1.1 255.255.255.128
Branch3(config-subif)#no shut
Branch3(config-subif)#no shutdown
Branch3(config-subif)#
Branch3(config-subif)#exit
Branch3(config)#iny
Branch3(config)#in
Branch3(config)#interface g
Branch3(config)#interface gigabitEthernet 0/0.20
Branch3(config-subif)#ip add
Branch3(config-subif)#ip address 192.168.1.129 255.255.255.192
Branch3(config-subif)#no shut
Branch3(config-subif)#no shutdown
Branch3(config-subif)#
Branch3(config)#router eigrp 22
Branch3(config-router)#no auto-summary
Branch3(config-router)#network 192.168.1.1 0.0.0.127
Branch3(config-router)#network 192.168.1.129 0.0.0.63
Branch3(config-router)#network 192.168.1.193 0.0.0.31
Branch3(config-router)#network 192.168.1.225 0.0.0.15
Branch3(config-router)#network 192.168.1.241 0.0.0.3
Branch3(config-router)#network 192.168.0.1 0.0.0.255
Branch3(config-router)#network 192.168.3.250 0.0.0.3
Branch3(config-router)#network 192.168.3.242 0.0.0.3
Branch3(config-router)#pass
Branch3(config-router)#passive-interface g
Branch3(config-router)#passive-interface gigabitEthernet 0/0.10
Branch3(config-router)#passive-interface gigabitEthernet 0/0.20
Branch3(config-router)#passive-interface gigabitEthernet 0/0.30
Branch3(config-router)#passive-interface gigabitEthernet 0/0.88
Branch3(config-router)#passive-interface gigabitEthernet 0/0.99
Branch3(config-router)#passive-interface gigabitEthernet 0/1
Branch3(config)#interface serial 0/0/0
Branch3(config-if)#ip summary-address eigrp 22 192.168.0.0 255.255.254.0 ?
<1-255> Administrative distance
<cr>
Branch3(config-if)#ip summary-address eigrp 22 192.168.0.0 255.255.254.0 5
Branch3(config-if)#exit
Branch3(config)#int serial 0/0/1
Branch3(config-if)#ip summary-address eigrp 22 192.168.0.0 255.255.254.0 5
Branch1(config)#router eigrp 22
Branch1(config-router)#redi
Branch1(config-router)#redistribute sta
Branch1(config-router)#redistribute static
Branch1(config)#interface gigabitEthernet 0/0
Branch1(config-if)#ip address dhcp
Branch1(config-if)#exit
Branch1(config)#
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0/0 assigned DHCP address 209.165.202.130, mask 255.255.255.224, hostname Branch1
Branch3(config)#ip dhcp pool Students
Branch3(dhcp-config)#network 192.168.1.0 255.255.255.128
Branch3(dhcp-config)#default-router 192.168.1.1 255.255.255.128
Branch3(dhcp-config)#default-router 192.168.1.1
Branch3(dhcp-config)#dns-server 209.165.201.14
Branch3(dhcp-config)#exit
Branch3(config)#ip dhcp excluded-address 192.168.1.1 192.168.1.10
Branch3(config)#
Branch7(config)#ipv6 unicast-routing
Branch7(config)#ipv6 router eigrp 222
Branch7(config-rtr)#no shutdown
Branch7#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Branch7(config)#int
Branch7(config)#interface g
Branch7(config)#interface gigabitEthernet 0/0
Branch7(config-if)#ipv
Branch7(config-if)#ipv6 eig
Branch7(config-if)#ipv6 eigrp 222
Branch7(config-if)#exit
Branch7(config)#int
Branch7(config)#interface g
Branch7(config)#interface gigabitEthernet 0/1
Branch7(config-if)#ipv
Branch7(config-if)#ipv6 eig
Branch7(config-if)#ipv6 eigrp 222
Branch7(config-if)#exit
Branch7(config)#int
Branch7(config)#interface s
Branch7(config)#interface serial 0/0/0
Branch7(config-if)#ipv
Branch7(config-if)#ipv6 int
Branch7(config-if)#ipv6 g
Branch7(config-if)#ipv6 eig
Branch7(config-if)#ipv6 eigrp 222
Branch7(config-if)#exit
Branch7(config)#int
Branch7(config)#interface s
Branch7(config)#interface serial 0/0/1
Branch7(config-if)#ipv
Branch7(config-if)#ipv6 eig
Branch7(config-if)#ipv6 eigrp 222
Branch7(config-if)#exit
Branch4#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Branch4(config)#ip rou
Branch4(config)#ipv
Branch4(config)#ipv6 route
Branch4(config)#ipv6 route ::/0 s
Branch4(config)#ipv6 route ::/0 serial 0/1/0
Branch4(config)#ipv
Branch4(config)#ipv6 route
Branch4(config)#ipv6 router
Branch4(config)#ipv6 router ei
Branch4(config)#ipv6 router eigrp 222
Branch4(config-rtr)#redi
Branch4(config-rtr)#redistribute st
Branch4(config-rtr)#redistribute static
S3(config)#banner motd c get out c
S3(config)#banner motd c getout c
S3(config)#banner motd c warning c
S3(config)#
%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet0/1 (1), with S1 FastEthernet0/3 (99).
S3(config)#li
S3(config)#line co
S3(config)#line console 0
S3(config-line)#pass
S3(config-line)#password ciso
S3(config-line)#password cisco
S3(config-line)#login
S3(config-line)#login
S3(config-line)#exit
S3(config)#ena
S3(config)#enable se
S3(config)#enable secret class
S3(config)#
S3(config)#ser
S3(config)#service pas
S3(config)#service password-encryption
S3(config-if)#exit
S3(config)#vlan 10
S3(config-vlan)#name Students
S3(config-vlan)#exit
S3(config)#vlan 20
S3(config-vlan)#name Faculty/Staff
S3(config-vlan)#exit
S3(config)#vl
S3(config)#vlan 30
S3(config-vlan)#name Guest(Default)
S3(config-vlan)#exit
S3(config)#interface range fastEthernet 0/5-11
S3(config-if-range)#switchport mode access
S3(config-if-range)#switchport access vlan 10
S3(config-if-range)#exit
S3(config)#interface range fastEthernet 0/12-17
S3(config-if-range)#switchport mode access
S3(config-if-range)#switchport access vlan 20
S3(config-if-range)#exit
S3(config)#interface range fastEthernet 0/18-24
S3(config-if-range)#switchport access vlan 30
S3(config-if-range)#exit
S3(config)#
S3(config)#interface range fastEthernet 0/1-4
S3(config-if-range)#sw
S3(config-if-range)#switchport mo
S3(config-if-range)#switchport mode tr
S3(config-if-range)#switchport tr
S3(config-if-range)#switchport trunk n
S3(config-if-range)#switchport trunk native v
S3(config-if-range)#switchport trunk native vlan 99
S3(config-if-range)#exit
S3(config)#
S1(config)#interface range fastEthernet 0/3-4
S1(config-if-range)#switchport trunk native vlan 99
Branch7(config-rtr)#eigrp router-id 7.7.7.7
S3(config)#interface range fastEthernet 0/18-24
S3(config-if-range)#switchport port-security
S3(config-if-range)#switchport port-security maximum 1
S3(config-if-range)#switchport port-security violation shutdown
S3(config-if-range)#switchport port-security mac-address sticky
S2(config)#interface range fastEthernet 0/1-2
S2(config-if-range)#switchport mode trunk
S2(config-if-range)#
S1(config)#interface range fastEthernet 0/1-4
S1(config-if-range)#switchport mode trunk
S3(config)#interface fastEthernet 0/15
S3(config-if)#spanning-tree portfast
S3(config-if)#spanning-tree bpduguard enable
S3(config-if)#exit
S3(config)#
