一. Wpa_supplicant 啓動腳本：
wpa_supplicant -Dnl80211 -iwlan0 -c/data/misc/wifi/wpa_supplicant.conf -O/data/misc/wifi/sockets
二. Wpa_cli 啓動:
wpa_cli是命令行界面下的無線網連接工具，在wpa_supplicant運行的基礎上，打開wpa_cli:
wpa_cli -iwlan0 -p/data/misc/wifi/sockets
三. wpa_cli 整套指令如下：
root@:/system/bin # wpa_cli -iwlan0 -p/data/misc/wifi/sockets
wpa_cli v2.5-devel-6.0
Copyright (c) 2004-2015, Jouni Malinen <[email protected]> and contributors
This software may be distributed under the terms of the BSD license.
See README for more details.
Interactive mode
> help
commands:
status [verbose] = get current WPA/EAPOL/EAP status
ifname = get current interface name
ping = pings wpa_supplicant
relog = re-open log-file (allow rolling logs)
note <text> = add a note to wpa_supplicant debug log
mib = get MIB variables (dot1x, dot11)
help [command] = show usage help
interface [ifname] = show interfaces/select interface
level <debug level> = change debug level
license = show full wpa_cli license
quit = exit wpa_cli
set = set variables (shows list of variables when run without arguments)
dump = dump config variables
get <name> = get information
logon = IEEE 802.1X EAPOL state machine logon
logoff = IEEE 802.1X EAPOL state machine logoff
pmksa = show PMKSA cache
pmksa_flush = flush PMKSA cache entries
reassociate = force reassociation
reattach = force reassociation back to the same BSS
preauthenticate <BSSID> = force preauthentication
identity <network id> <identity> = configure identity for an SSID
password <network id> <password> = configure password for an SSID
new_password <network id> <password> = change password for an SSID
pin <network id> <pin> = configure pin for an SSID
otp <network id> <password> = configure one-time-password for an SSID
passphrase <network id> <passphrase> = configure private key passphrase
for an SSID
sim <network id> <pin> = report SIM operation result
bssid <network id> <BSSID> = set preferred BSSID for an SSID
blacklist <BSSID> = add a BSSID to the blacklist
blacklist clear = clear the blacklist
blacklist = display the blacklist
log_level <level> [<timestamp>] = update the log level/timestamp
log_level = display the current log level and log options
list_networks = list configured networks
select_network <network id> = select a network (disable others)
enable_network <network id> = enable a network
disable_network <network id> = disable a network
add_network = add a network
remove_network <network id> = remove a network
set_network <network id> <variable> <value> = set network variables (shows
list of variables when run without arguments)
get_network <network id> <variable> = get network variables
dup_network <src network id> <dst network id> <variable> = duplicate network variables
list_creds = list configured credentials
add_cred = add a credential
remove_cred <cred id> = remove a credential
set_cred <cred id> <variable> <value> = set credential variables
get_cred <cred id> <variable> = get credential variables
save_config = save the current configuration
disconnect = disconnect and wait for reassociate/reconnect command before
connecting
reconnect = like reassociate, but only takes effect if already disconnected
scan = request new BSS scan
scan_results = get latest scan results
bss <<idx> | <bssid>> = get detailed scan result info
get_capability <eap/pairwise/group/key_mgmt/proto/auth_alg/channels/freq/modes> = get capabilities
reconfigure = force wpa_supplicant to re-read its configuration file
terminate = terminate wpa_supplicant
interface_add <ifname> <confname> <driver> <ctrl_interface> <driver_param>
<bridge_name> = adds new interface, all parameters but <ifname>
are optional
interface_remove <ifname> = removes the interface
interface_list = list available interfaces
ap_scan <value> = set ap_scan parameter
scan_interval <value> = set scan_interval parameter (in seconds)
bss_expire_age <value> = set BSS expiration age parameter
bss_expire_count <value> = set BSS expiration scan count parameter
bss_flush <value> = set BSS flush age (0 by default)
stkstart <addr> = request STK negotiation with <addr>
ft_ds <addr> = request over-the-DS FT with <addr>
wps_pbc [BSSID] = start Wi-Fi Protected Setup: Push Button Configuration
wps_pin <BSSID> [PIN] = start WPS PIN method (returns PIN, if not hardcoded)
wps_check_pin <PIN> = verify PIN checksum
wps_cancel Cancels the pending WPS operation
wps_nfc [BSSID] = start Wi-Fi Protected Setup: NFC
wps_nfc_config_token <WPS|NDEF> = build configuration token
wps_nfc_token <WPS|NDEF> = create password token
wps_nfc_tag_read <hexdump of payload> = report read NFC tag with WPS data
nfc_get_handover_req <NDEF> <WPS> = create NFC handover request
nfc_get_handover_sel <NDEF> <WPS> = create NFC handover select
nfc_report_handover <role> <type> <hexdump of req> <hexdump of sel> = report completed NFC handover
wps_reg <BSSID> <AP PIN> = start WPS Registrar to configure an AP
wps_ap_pin [params..] = enable/disable AP PIN
wps_er_start [IP address] = start Wi-Fi Protected Setup External Registrar
wps_er_stop = stop Wi-Fi Protected Setup External Registrar
wps_er_pin <UUID> <PIN> = add an Enrollee PIN to External Registrar
wps_er_pbc <UUID> = accept an Enrollee PBC using External Registrar
wps_er_learn <UUID> <PIN> = learn AP configuration
wps_er_set_config <UUID> <network id> = set AP configuration for enrolling
wps_er_config <UUID> <PIN> <SSID> <auth> <encr> <key> = configure AP
wps_er_nfc_config_token <WPS/NDEF> <UUID> = build NFC configuration token
ibss_rsn <addr> = request RSN authentication with <addr> in IBSS
sta <addr> = get information about an associated station (AP)
all_sta = get information about all associated stations (AP)
deauthenticate <addr> = deauthenticate a station
disassociate <addr> = disassociate a station
chan_switch <cs_count> <freq> [sec_channel_offset=] [center_freq1=] [center_freq2=] [bandwidth=] [blocktx] [ht|vht] = CSA parameters
suspend = notification of suspend/hibernate
resume = notification of resume/thaw
roam <addr> = roam to the specified BSS
p2p_find [timeout] [type=*] = find P2P Devices for up-to timeout seconds
p2p_stop_find = stop P2P Devices search
p2p_asp_provision <addr> adv_id=<adv_id> conncap=<conncap> [info=<infodata>] = provision with a P2P ASP Device
p2p_asp_provision_resp <addr> adv_id=<adv_id> [role<conncap>] [info=<infodata>] = provision with a P2P ASP Device
p2p_connect <addr> <"pbc"|PIN> [ht40] = connect to a P2P Device
p2p_listen [timeout] = listen for P2P Devices for up-to timeout seconds
p2p_group_remove <ifname> = remove P2P group interface (terminate group if GO)
p2p_group_add [ht40] = add a new P2P group (local end as GO)
p2p_prov_disc <addr> <method> = request provisioning discovery
p2p_get_passphrase = get the passphrase for a group (GO only)
p2p_serv_disc_req <addr> <TLVs> = schedule service discovery request
p2p_serv_disc_cancel_req <id> = cancel pending service discovery request
p2p_serv_disc_resp <freq> <addr> <dialog token> <TLVs> = service discovery response
p2p_service_update = indicate change in local services
p2p_serv_disc_external <external> = set external processing of service discovery
p2p_service_flush = remove all stored service entries
p2p_service_add <bonjour|upnp|asp> <query|version> <response|service> = add a local service
p2p_service_rep asp <auto> <adv_id> <svc_state> <svc_string> [<svc_info>] = replace local ASP service
p2p_service_del <bonjour|upnp> <query|version> [|service] = remove a local service
p2p_reject <addr> = reject connection attempts from a specific peer
p2p_invite <cmd> [peer=addr] = invite peer
p2p_peers [discovered] = list known (optionally, only fully discovered) P2P peers
p2p_peer <address> = show information about known P2P peer
p2p_set <field> <value> = set a P2P parameter
p2p_flush = flush P2P state
p2p_cancel = cancel P2P group formation
p2p_unauthorize <address> = unauthorize a peer
p2p_presence_req [<duration> <interval>] [<duration> <interval>] = request GO presence
p2p_ext_listen [<period> <interval>] = set extended listen timing
p2p_remove_client <address|iface=address> = remove a peer from all groups
wfd_subelem_set <subelem> [contents] = set Wi-Fi Display subelement
wfd_subelem_get <subelem> = get Wi-Fi Display subelement
fetch_anqp = fetch ANQP information for all APs
stop_fetch_anqp = stop fetch_anqp operation
interworking_select [auto] = perform Interworking network selection
interworking_connect <BSSID> = connect using Interworking credentials
interworking_add_network <BSSID> = connect using Interworking credentials
anqp_get <addr> <info id>[,<info id>]... = request ANQP information
gas_request <addr> <AdvProtoID> [QueryReq] = GAS request
gas_response_get <addr> <dialog token> [start,len] = Fetch last GAS response
hs20_anqp_get <addr> <subtype>[,<subtype>]... = request HS 2.0 ANQP information
nai_home_realm_list <addr> <home realm> = get HS20 nai home realm list
hs20_icon_request <addr> <icon name> = get Hotspot 2.0 OSU icon
fetch_osu = fetch OSU provider information from all APs
cancel_fetch_osu = cancel fetch_osu command
sta_autoconnect <0/1> = disable/enable automatic reconnection
tdls_discover <addr> = request TDLS discovery with <addr>
tdls_setup <addr> = request TDLS setup with <addr>
tdls_teardown <addr> = tear down TDLS with <addr>
tdls_link_status <addr> = TDLS link status with <addr>
wmm_ac_addts <uplink/downlink/bidi> <tsid=0..7> <up=0..7> [nominal_msdu_size=#] [mean_data_rate=#] [min_phy_rate=#] [sba=#] [fixed_nominal_msdu] = add WMM-AC traffic stream
wmm_ac_delts <tsid> = delete WMM-AC traffic stream
wmm_ac_status = show status for Wireless Multi-Media Admission-Control
tdls_chan_switch <addr> <oper class> <freq> [sec_channel_offset=] [center_freq1=] [center_freq2=] [bandwidth=] [ht|vht] = enable channel switching with TDLS peer
tdls_cancel_chan_switch <addr> = disable channel switching with TDLS peer <addr>
signal_poll = get signal parameters
pktcnt_poll = get TX/RX packet counters
reauthenticate = trigger IEEE 802.1X/EAPOL reauthentication
wnm_sleep <enter/exit> [interval=#] = enter/exit WNM-Sleep mode
wnm_bss_query <query reason> = Send BSS Transition Management Query
raw <params..> = Sent unprocessed command
flush = flush wpa_supplicant state
driver <command> = driver private commands
radio_work = radio_work <show/add/done>
vendor <vendor id> <command id> [<hex formatted command argument>] = Send vendor command
neighbor_rep_request [ssid=<SSID>] = Trigger request to AP for neighboring AP report (with optional given SSID, default: current SSID)
erp_flush = flush ERP keys
mac_rand_scan <scan|sched|pno|all> enable=<0/1> [addr=mac-address mask=mac-address-mask] = scan MAC randomization
>
常用的指令如下：
1. 打開debug log : wpa_cli -iwlan0 -p/data/misc/wifi/sockets log_level debug
2. scan：打開後掃描AP
3. scan_results：顯示掃描結果
4. status：列出目前的聯網狀態。
5. ist_networks：列出所有備選網絡。目前正連接到的網絡會標[CURRENT]，禁用的網絡會標[DISABLE]。
6. add_network：增加一個備選網絡，輸出新網絡的號碼（這個號碼替代下文的[network_id]）。注意新網絡此時是禁用狀態。
7. set_network [network_id] ssid “Your SSID”：設置無線網的名稱（SSID）
8. set_network [network_id] key_mgmt WPA-PSK：設置無線網的加密方式爲WPA-PSK/WPA2-PSK
9. set_network [network_id] psk “Your Password”：設置無線網的PSK密碼
10. enable_network [network_id]：啓用網絡。啓用後如果系統搜索到了這個網絡，就會嘗試連接。
11. disable_network [network_id]：禁用網絡。
12. save_config：保存配置。
e.g.
>add_network
0<--- 新網絡的號碼
>set_network 0 ssid "TP-LINK_HyFi_75"
ok
>set_network 0 key_mgmt WPA-PSK
ok
>set_network 0 psk "147258369"
ok
>enable_network 0
ok
>save_config<--------別忘了這個，否則重啓之後網絡配置可能丟失
ok
四. demo
wpa_supplicant log:
wlan0: Control interface command 'SCAN TYPE=ONLY' //scan
wlan0: Control interface command 'ADD_NETWORK' //add_network x : 增加一個備選網絡，輸出新網絡的號碼（這個號碼替代下文的[network_id]）。注意新網絡此時是禁用狀態
CTRL_IFACE: ADD_NETWORK
wlan0: Control interface command 'SET_NETWORK [REMOVED]' //set_network [network_id] ssid “Your SSID”：設置無線網的名稱（SSID）
CTRL_IFACE: SET_NETWORK id=0 name='ssid'
ssid - hexdump(len=15): 54 50 2d 4c 49 4e 4b 5f 5a 48 45 4e 32 2e 34
wlan0: Control interface command 'SET_NETWORK [REMOVED]' //set_network [network_id] key_mgmt WPA-PSK：設置無線網的加密方式爲WPA-PSK/WPA2-PSK
CTRL_IFACE: SET_NETWORK id=0 name='key_mgmt'
key_mgmt: 0x4
wlan0: Control interface command 'SET_NETWORK [REMOVED]' //set_network [network_id] priority x：設置network 的優先級
CTRL_IFACE: SET_NETWORK id=0 name='priority'
priority=0 (0x0)
wlan0: Control interface command 'ENABLE_NETWORK 0' //enable_network [network_id]：啓用網絡。啓用後如果系統搜索到了這個網絡，就會嘗試連接
CTRL_IFACE: ENABLE_NETWORK id=0
wlan0: Control interface command 'SELECT_NETWORK 0' //select_network [networi_id]: 選擇network進行連接
CTRL_IFACE: SELECT_NETWORK id=0
Fast associate: Old scan results
wlan0: Setting scan request: 0.000000 sec
wlan0: Control interface command 'RECONNECT' // reconnect : like reassociate, but only takes effect if already disconnected
實操：
> scan
OK
<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=
<3>CTRL-EVENT-SCAN-STARTED
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
<3>CTRL-EVENT-STATE-CHANGE id=-1 state=2 BSSID=00:00:00:00:00:00 SSID=
<3>CTRL-EVENT-NETWORK-NOT-FOUND
>
> scan_results
bssid / frequency / signal level / flags / ssid
04:a1:51:8a:9c:ae 5745 -53 [WPA2-PSK-CCMP][WPS][ESS] NETGEAR-63-5G
8c:be:be:2d:3f:28 5785 -60 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] XIaomi_5G
50:bd:5f:15:36:18 5785 -63 [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] TP-LINK_ZHEN_5G
ec:26:ca:3a:fa:ba 5745 -68 [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS] Lw_5G
50:bd:5f:15:36:19 2442 -53 [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] TP-LINK_ZHEN_2.4G
8c:be:be:2d:3f:27 2437 -55 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] Xiaomi_2.4G
80:89:17:ab:c0:7f 2437 -62 [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] sa10
ec:26:ca:87:83:02 2437 -64 [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS] TP-LINK_8302
ec:26:ca:3a:fa:bb 2422 -65 [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS] Lw_24G
80:89:17:ab:c0:7e 5745 -73 [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] sa10_5G
28:6c:07:51:1b:46 2447 -55 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] Xiaomi_test_ZZ
40:e3:d6:8f:59:62 2462 -56 [WPA2-EAP-CCMP][ESS] mtkinternet
40:e3:d6:8f:59:61 2462 -59 [WPA-EAP-CCMP+TKIP][WPA2-EAP-CCMP+TKIP][ESS]
98:fc:11:4d:c7:a2 2412 -61 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] linksys
50:bd:5f:93:ee:ac 2412 -63 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] abcd
28:6c:07:51:1b:47 5745 -82 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] Xiaomi_test_ZZ_5G
38:97:d6:18:c4:12 2412 -60 [WPA-PSK-TKIP][WPA2-PSK-TKIP][ESS] wnw
c8:02:10:b4:ab:61 2462 -69 [WPA2-PSK-CCMP][ESS] LG_MusicFlow_DL_3193
70:f9:6d:31:e0:00 2462 -75 [WPA2-PSK-CCMP][ESS] MPR-wifi
80:89:17:f4:cb:77 2437 -78 [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] TP-LINK_2.4G_MT3
6c:f3:7f:38:ff:eb 5785 -85 [WPA2-EAP-CCMP][ESS] mtkemp
6c:f3:7f:38:ff:ea 5785 -86 [WPA2-EAP-CCMP][ESS] mtkinternet
64:09:80:1f:17:be 2462 -75 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] SS2_Xiaomi
40:e3:d6:8f:59:41 2462 -75 [WPA-EAP-CCMP+TKIP][WPA2-EAP-CCMP+TKIP][ESS]
ec:6c:9f:22:de:01 2437 -75 [WPA2-PSK-CCMP][ESS] estar
40:e3:d6:8f:59:43 2462 -76 [WPA2-EAP-CCMP][ESS] mtkemp
38:97:d6:18:d4:32 2412 -76 [WPA-PSK-TKIP][WPA2-PSK-TKIP][ESS] wnw
40:e3:d6:8f:59:42 2462 -77 [WPA2-EAP-CCMP][ESS] mtkinternet
6c:f3:7f:38:ff:e9 5785 -87 [WPA-EAP-CCMP+TKIP][WPA2-EAP-CCMP+TKIP][ESS]
80:89:17:f4:cb:76 5785 -89 [WPA-PSK-CCMP][WPA2-PSK-CCMP][WPS][ESS] TP-LINK_5G_MT3
b8:a3:86:55:8f:b2 2437 -79 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] SS7_VPN
40:e3:d6:8f:59:83 2462 -81 [WPA2-EAP-CCMP][ESS] mtkemp
38:97:d6:18:c4:00 5805 -85 [WPA-PSK-TKIP][WPA2-PSK-TKIP][ESS] wnwyanfa
40:e3:d6:8f:59:81 2462 -82 [WPA-EAP-CCMP+TKIP][WPA2-EAP-CCMP+TKIP][ESS]
0c:72:2c:4f:41:66 2427 -88 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] 0000aaaa
40:e3:d6:8f:59:64 2462 -57 [WEP][ESS] mtklab
40:e3:d6:8f:59:44 2462 -75 [WEP][ESS] mtklab
6c:f3:7f:38:ff:ec 5785 -86 [WEP][ESS] mtklab
04:a1:51:8a:9c:ac 2422 -56 [WPS][ESS] NETGEAR-63-2.4G
e4:d3:32:cd:74:b3 2412 -57 [WPS][ESS] rongweim
40:e3:d6:8f:59:60 2462 -57 [ESS] mtkguest
fc:75:16:a3:95:d0 2462 -76 [WPS][ESS] dlink
00:0c:43:28:08:88 2437 -78 [ESS] MT7623_AP_2.4G
6c:f3:7f:38:ff:e8 5785 -85 [ESS] mtkguest
40:e3:d6:8f:59:40 2462 -75 [ESS] mtkguest
6c:f3:7f:38:ff:e0 2462 -85 [ESS] mtkguest
> list_network
network id / ssid / bssid / flags
0 Xiaomi_5G any [DISABLED]
1 D8_5GHZ any [DISABLED]
2 SS7_VPN any [DISABLED]
3 Xiaomi_2.4G any [DISABLED]
4 XIaomi_5G any [DISABLED]
5 hello any [DISABLED]
6 NETGEAR6200 any [DISABLED]
7 NETGEAR6200_5G any [DISABLED]
8 NETGEAR-63-2.4G any [DISABLED]
9 DLink88_24G any [DISABLED]
> add_network 10
10
> set_network 10 ssid "NETGEAR-63-5G"
OK
> list_network
network id / ssid / bssid / flags
0 Xiaomi_5G any [DISABLED]
1 D8_5GHZ any [DISABLED]
2 SS7_VPN any [DISABLED]
3 Xiaomi_2.4G any [DISABLED]
4 XIaomi_5G any [DISABLED]
5 hello any [DISABLED]
6 NETGEAR6200 any [DISABLED]
7 NETGEAR6200_5G any [DISABLED]
8 NETGEAR-63-2.4G any [DISABLED]
9 DLink88_24G any [DISABLED]
10 NETGEAR-63-5G any [DISABLED]
> set_network 10 key_mgmt WPA-PSK
OK
> set_network 10 psk "11111111"
OK
> get_network 10 key_mgmt
WPA-PSK
> get_network 10 psk
*
> enable_network 10
OK
<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=
<3>CTRL-EVENT-SCAN-STARTED
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
<3>Trying to associate with [18434.676000] 80211> Connect bssid 04:a1:51:8a:9c:ae
> select_network 10
OK
> reconnect
OK
> list_network
network id / ssid / bssid / flags
0 Xiaomi_5G any [DISABLED]
1 D8_5GHZ any [DISABLED]
2 SS7_VPN any [DISABLED]
3 Xiaomi_2.4G any [DISABLED]
4 XIaomi_5G any [DISABLED]
5 hello any [DISABLED]
6 NETGEAR6200 any [DISABLED]
7 NETGEAR6200_5G any [DISABLED]
8 NETGEAR-63-2.4G any [DISABLED]
9 DLink88_24G any [DISABLED]
10 NETGEAR-63-5G any [CURRENT]
> save_config
OK
> status
bssid=04:a1:51:8a:9c:ae
freq=5745
ssid=NETGEAR-63-5G
id=10
mode=station
pairwise_cipher=CCMP
group_cipher=CCMP
key_mgmt=WPA2-PSK
wpa_state=COMPLETED
ip_address=10.0.0.5
address=00:6c:fd:ab:68:be
uuid=12345678-9abc-def0-1234-56789abcdef0
<3>CTRL-EVENT-STATE-CHANGE id=10 state=9 BSSID=04:a1:51:8a:9c:ae SSID=NETGEAR-63-5G
<3>CTRL-EVENT-CONNECTED - connection to 04:a1:51:8a:9c:ae completed (auth) [id=10 id_str=]
保存後的wap_supplicant.conf
root@:/system/bin # cd /data/misc/wifi/
root@:/data/misc/wifi # cat wpa_supplicant
wpa_supplicant.conf wpa_supplicant/
at wpa_supplicant.conf <
ctrl_interface=/data/misc/wifi/sockets
driver_param=p2p_capable=0
update_config=1
uuid=12345678-9abc-def0-1234-56789abcdef0
device_name=full
manufacturer= Group Co., Ltd
model_name=Android TV
model_number=Android TV
serial_number=123456789
device_type=10-0050F204-5
os_version=01020300
config_methods=physical_display virtual_push_button
external_sim=1
wowlan_triggers=magic_pkt
network={
ssid="Xiaomi_5G"
psk="26630099"
key_mgmt=WPA-PSK
priority=12
disabled=1
}
network={
ssid="D8_5GHZ"
key_mgmt=NONE
priority=9
disabled=1
}
network={
ssid="SS7_VPN"
psk="12345678"
key_mgmt=WPA-PSK
priority=11
disabled=1
}
network={
ssid="Xiaomi_2.4G"
psk="26630099"
key_mgmt=WPA-PSK
priority=13
disabled=1
}
network={
ssid="XIaomi_5G"
psk="26630099"
key_mgmt=WPA-PSK
priority=18
disabled=1
}
network={
ssid="hello"
key_mgmt=NONE
priority=17
disabled=1
}
network={
ssid="NETGEAR6200"
psk="12345678"
key_mgmt=WPA-PSK
priority=19
disabled=1
}
network={
ssid="NETGEAR6200_5G"
psk="12345678"
key_mgmt=WPA-PSK
priority=27
disabled=1
}
network={
ssid="NETGEAR-63-2.4G"
psk="11111111"
key_mgmt=WPA-PSK
priority=56
disabled=1
}
network={
ssid="DLink88_24G"
psk="12345678"
key_mgmt=WPA-PSK
priority=38
disabled=1
}
network={
ssid="NETGEAR-63-5G"
psk="11111111"
key_mgmt=WPA-PSK
}