CentOS7 無法使用yum命令，無法更新解決方法
- 前言
- 設置網卡開機自動啓動
- 設置國內dns服務器系統
- 修改CentOS-Base.repo中的地址
前言
剛安裝完的CentOS7的系統，發現無法使用yum命令進行更新，在更新的時候會出現下面這種內容，爲此問題有以下這些解決方案可以嘗試。
One of the configured repositories failed (Unknown),
and yum doesn't have enough cached data to continue. At this point the only
safe thing yum can do is fail. There are a few ways to work "fix" this:
1. Contact the upstream for the repository and get them to fix the problem.
2. Reconfigure the baseurl/etc. for the repository, to point to a working
upstream. This is most often useful if you are using a newer
distribution release than is supported by the repository (and the
packages for the previous distribution release still work).
3. Disable the repository, so yum won't use it by default. Yum will then
just ignore the repository until you permanently enable it again or use
--enablerepo for temporary usage:
yum-config-manager --disable <repoid>
4. Configure the failing repository to be skipped, if it is unavailable.
Note that yum will try to contact the repo. when it runs most commands,
so will have to try and fail each time (and thus. yum will be be much
slower). If it is a very temporary problem though, this is often a nice
compromise:
yum-config-manager --save --setopt=<repoid>.skip_if_unavailable=true
24
1
One of the configured repositories failed (Unknown),
2
and yum doesn't have enough cached data to continue. At this point the only
3
safe thing yum can do is fail. There are a few ways to work "fix" this:
4
5
1. Contact the upstream for the repository and get them to fix the problem.
6
7
2. Reconfigure the baseurl/etc. for the repository, to point to a working
8
upstream. This is most often useful if you are using a newer
9
distribution release than is supported by the repository (and the
10
packages for the previous distribution release still work).
11
12
3. Disable the repository, so yum won't use it by default. Yum will then
13
just ignore the repository until you permanently enable it again or use
14
--enablerepo for temporary usage:
15
16
yum-config-manager --disable <repoid>
17
18
4. Configure the failing repository to be skipped, if it is unavailable.
19
Note that yum will try to contact the repo. when it runs most commands,
20
so will have to try and fail each time (and thus. yum will be be much
21
slower). If it is a very temporary problem though, this is often a nice
22
compromise:
23
24
yum-config-manager --save --setopt=<repoid>.skip_if_unavailable=true
設置網卡開機自動啓動
針對這個問題首先要確認網卡是否已經啓動了，CentOS7最開始安裝完的時候網卡可能會是關閉的，需要自己自行開啓。
確保自己使用的是root賬號，若不是，請自行更換。
1、進入/etc/sysconfig/network-scripts 目錄。即輸入命令 "cd /etc/sysconfig/network-scripts" ，使用命令 "ls -a" 可以查看該目錄下的所有文件。
2、修改ifcfg-ens33的網卡配置文件（CentOS7修改了網卡命名規則，不再是eth0了，而是ifcfg-eno+數字）。輸入命令 "vi ifcfg-ens33" 進入vi編輯器，按下"i"或者"insert"鍵進入編輯模式。
3、將 "ONBOOT" 的值修改爲 "yes" ，之後按esc退出編輯模式，輸入 ":wq" 保存退出
4、重啓系統或者重啓網卡，輸入命令 "reboot" 或 "service network restart"。
設置國內dns服務器
若已經開啓了網卡還是存在該問題可以嘗試配置下國內的dns。
1、輸入命令 "vi /etc/resolv.conf"
2、添加 "nameserver 114.114.114.114"
3、保存後，重啓系統或者重啓網卡，輸入命令 "reboot" 或 "service network restart"。
修改CentOS-Base.repo中的地址
若上述方法還是無效可以嘗試修改CentOS-Base.repo中的地址
1、進入 "/etc/yum.repos.d" 。
2、編輯 "vi CentOS-Base.repo" 。
3、將所有的 "mirrorlist" 註釋掉，將所有的 "baseurl" 取消註釋。
4、保存後，重啓系統，輸入命令 "reboot" 。