5G-NSA組網參數配置

PCC頻點配置

ADD PCCFREQCFG: PccDlEarfcn=1300,PreferredPccPriority=1, PccA4RsrpThd=-105, PccA4RsrqThd=-20;

 SSB頻點配置

 NR側中心頻點爲513000,絕對頻點號方式例子，Ssb頻點爲512964：

ADD NRSCGFREQCONFIG: PccDlEarfcn=1300, ScgDlArfcn=512964,ScgDlArfcnPriority=1;

NR側中心頻點爲513000,GSCN號6312對應504990：

ADD NRSCGFREQCONFIG: PccDlEarfcn=1300,ScgDlArfcn=504990, ScgDlArfcnPriority=1;

 MFBI頻點配置

(C10SPC050及以後版本需要配置，和SCG SSB頻點保持一致，只有在頻點約束範圍內的SSB頻點才需要配置，如果不在範圍不需要配置。不配置會導致接入失敗，升級場景需要特別注意手動增加。下面爲參考樣例) 範圍爲：158200 – 160600，285400 – 303400，386000 – 398000，402000 – 404000，422000 – 434000，514000 – 537999，620000 – 653333，2054166 – 2084999。頻點和上面配置的SCG SSB頻點保持一致。當前省內開通60M或100M，一般SSB頻點爲509004或512964，則MFBI頻點不需要添加。

ADD NRMFBIFREQ：DlArfcn=522966， FrequencyBand=N41;

 NR鄰區PLMN名單配置

（制式選擇NR，gNBIdLength請與5G側gNodeBFunction的gNBIdLength保持一致）。注意：若一定要打開，則必須注意首次配置時，必須與NR側保持一致，否則會導致NSA業務接入失敗；若NR側修改gNBIdLength，則LTE側必須同步修改，否則會導致NSA業務接入失敗。現網FDD1800和NR都配爲22。

ADD NCELLPLMNLIST: Mcc="460",Mnc="00", RatType=NR, gNBIdLength=22;

 NR外部小區配置

NR側中心頻點爲513000,絕對頻點號方式例子，SSB頻點爲512964：

ADD NREXTERNALCELL: Mcc="460",Mnc="00", GnodebId=531809, CellId=xx, DlArfcn=512964,UlArfcnConfigInd=NOT_CFG, PhyCellId=0, Tac=22547;

NR側中心頻點爲513000,GSCN號6411對應SSB頻點爲504990：

ADD NREXTERNALCELL: Mcc="460",Mnc="00", GnodebId=531809, CellId=xx, DlArfcn=504990,UlArfcnConfigInd=NOT_CFG, PhyCellId=0, Tac=22547;

 打開NSA DC算法開關

MOD NSADCMGMTCONFIG: LocalCellId=1,NsaDcAlgoSwitch= NSA_DC_CAPABILITY_SWITCH-1, NsaDcDefaultBearerMode=SCG_SPLIT_BEARER, NsaDcUeMcgUlAmbrRatio=30;

 增加NR相鄰頻點

SSB頻點配置SSB頻點(根據上面注意事項描述計算)，該條未加則4-5鄰區無法添加！！！

NR側中心頻點爲513000,絕對頻點號方式例子，Ssb頻點爲512964：

ADD NRNFREQ: LocalCellId=1,DlArfcn=512964, UlArfcnConfigInd= NOT_CFG;

NR側中心頻點爲513000,GSCN號6411對應Ssb頻點爲504990：

ADD NRNFREQ: LocalCellId=1,DlArfcn=504990, UlArfcnConfigInd= NOT_CFG;

 增加NR鄰區關係

ADD NRNRELATIONSHIP: LocalCellId=1,Mcc="460", Mnc="00", GnodebId=531809, CellId=0;

 關閉SIB2中是否攜帶upperlayerIndication-R15

MOD NSADCMGMTCONFIG:LocalCellId=1,UpperLayerIndicationSwitch=OFF;

 打開LTE側端管協同開關（關閉後CPE無法接入）

MOD UECOOPERATIONPARA: LocalCellId=1,SpecUserCooperationSwitch= SpecUeIdentifySwitch-1;

 修改X2自建立方式：通過S1進行X2自建立

打開接口建立策略開關：LTR與NR間X2自建立開關：開

MOD GLOBALPROCSWITCH:X2SONSETUPSWITCH=ON,X2SONLINKSETUPTYPE=X2_OVER_S1,INTERFACESETUPPOLICYSW=LTE_NR_X2_SON_SETUP_SW-1;

錨點站優先佔用參數配置

 4G測頻點添加

錨點小區NSA PCC錨點優先級配置爲7，非錨點小區該參數優先級配置爲0：

ADDPCCFREQCFG:PCCDLEARFCN=1300,PCCA4RSRPTHD=-107,NSAPCCANCHORINGPRIORITY=7;

ADD PCCFREQCFG:PCCDLEARFCN=37900,,PCCA4RSRPTHD=-107,NSAPCCANCHORINGPRIORITY=0;

 錨點和非錨點5G頻點添加

ADDNRSCGFREQCONFIG:PCCDLEARFCN=1300,SCGDLARFCN=509004,SCGDLARFCNPRIORITY=7;

 基站側數據修改

MODGLOBALPROCSWITCH:UECOMPATSWITCH=AbnormalUeHandleSwitch-1;

ADDUEINFO:UECAPINDEX=16,ACCESSSTRATUMRELEASE=5;

ADDUEINFO:UECAPINDEX=17,ACCESSSTRATUMRELEASE=7;

ADD UECOMPAT: Index=16,UeInfoType=UE_CAPABILITY, UeCapIndex=16,BlkLstCtrlSwitch=OSS_INTER_RAT_MR_SWITH_OFF-1&OSS_INTER_FREQ_MR_SWITH_OFF-1;

ADD UECOMPAT:INDEX=17,UEINFOTYPE=UE_CAPABILITY,UECAPINDEX=17,BLKLSTCTRLSWITCH=OSS_INTER_RAT_MR_SWITH_OFF-1&OSS_INTER_FREQ_MR_SWITH_OFF-1;

MODENODEBALGOSWITCH:HOSIGNALINGOPTSWITCH=ReduceMeasCtrlMesNumSwitch-0;

 錨點小區參數修改
MODNSADCMGMTCONFIG:LOCALCELLID=131,NSADCALGOSWITCH=NSA_DC_CAPABILITY_SWITCH-1&NSA_PCC_ANCHORING_SWITCH-1;

 非錨點小區修改

MOD NSADCMGMTCONFIG:LOCALCELLID=131,NSADCALGOSWITCH=NSA_PCC_ANCHORING_SWITCH-1;

MODENBCELLRSVDPARA:LOCALCELLID=131,RSVDU8PARA35=30;

ADDINTERFREQHOGROUP:LOCALCELLID=131,INTERFREQHOGROUPID=9,A3INTERFREQHOA1THDRSRP=-105,A3INTERFREQHOA2THDRSRP=-109;

MODENBCELLQCIRSVDPARA:LOCALCELLID=131,QCI=2-9,RSVDPARA15=109;

MODENBCELLQCIRSVDPARA:LOCALCELLID=131,QCI=9,RSVDSWPARA0=RsvdSwPara0_bit1-1;

MODENBCELLQCIRSVDPARA:LOCALCELLID=131,QCI=5,RSVDSWPARA0=RsvdSwPara0_bit1-1;

MODENBCELLQCIRSVDPARA:LOCALCELLID=131,QCI=1,RSVDSWPARA0=RsvdSwPara0_bit1-0;

MOD ENBCELLQCIRSVDPARA:LOCALCELLID=131,QCI=1,RSVDSWPARA0=RsvdSwPara0_bit2-1;

MODENBCELLRSVDPARA:LOCALCELLID=131,RSVDSWPARA6=RsvdSwPara6_bit18-1;

MODENBCELLRSVDPARA:LOCALCELLID=131,RSVDSWPARA6=RsvdSwPara6_bit19-1;

MODENBCELLRSVDPARA:LOCALCELLID=131,RSVDSWPARA6=RsvdSwPara6_bit20-1;

MODENBCELLRSVDPARA:LOCALCELLID=131,RSVDSWPARA6=RsvdSwPara6_bit21-1;

ADDEUTRANINTERNFREQ:LOCALCELLID=131,DLEARFCN=1300,ULEARFCNCFGIND=NOT_CFG,CELLRESELPRIORITYCFGIND=NOT_CFG,SPEEDDEPENDSPCFGIND=NOT_CFG,MEASBANDWIDTH=MBW100,PMAXCFGIND=NOT_CFG,QQUALMINCFGIND=NOT_CFG,INTERFREQCIOADJLIMITCFGIND=NOT_CFG;

 負載均衡准入開關

MODCELLMLBHO:LOCALCELLID=131,MLBMATCHOTHERFEATUREMODE=HoAdmitSwitch-0;

X2開關開啓
MODGLOBALPROCSWITCH:X2SONSETUPSWITCH=ON,X2SONLINKSETUPTYPE=X2_OVER_S1,INTERFACESETUPPOLICYSW=LTE_NR_X2_SON_SETUP_SW-1;