原创 OSPF特殊區域之stub和totally stub配置(二)

14.我們注意到R1路由學習到的本次實驗拓撲中所有的路由,在實際網絡應用中,R1路由並不需要學習到整個網絡路由。過多的路由條目會導致路由器變大,不利用路由查詢,同時也不利於網絡的收斂。OSPF網絡路由是通過LSA來進行通告。可以限制LSA的

原创 我的友情鏈接

51CTO博客開發小王凡人世界

原创 HSRP搶佔和接口追蹤

拓撲圖   實驗過程 1.       pc1的預配置 Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z.

原创 EIGRP路由彙總

EIGRP的彙總 拓撲圖   實驗過程 1.       R1的預配置 Router>en Router#config t Enter configuration commands, one per line.  End wi

原创 EIGRP路由彙總

EIGRP的彙總 拓撲圖   實驗過程 1.       R1的預配置 Router>en Router#config t Enter configuration commands, one per line.  End wi

原创 浮動靜態路由的配置

要求: 如下圖所示,R1有兩條路徑可以到達192.168.1.0/24網段,其中R2之間通過RIP學習到了192.168.1.0/24的路由,另外和R3之間,由於某些原因無法通過動態路由協議學習到路由,只能通過靜態路由的方式。 現在希望達到

原创 HSRP基礎實驗

拓撲圖   實驗過程 1.       pc的配置 Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z.

原创 路由標記過濾路由

實驗拓撲圖   實驗過程 1.       R1的預配置 Router>en Router#config t Enter configuration commands, one per line.  End with CNTL

原创 OSPF特殊區域之NSSA和totally NSSA配置(二)

16.把R4上的Area 1配置成NSSA區域 R4(config)#router ospf 1 R4(config-router)#area 1 nssa default-information-originate //defa

原创 基於route-map的路由過濾

實驗拓撲   實驗過程 1.R1的預配置 Router#config t Enter configuration commands, one per line.  End with CNTL/Z. Router(config

原创 VRRP接口追蹤和搶佔

拓撲圖   實驗過程 1.       pc1和pc2的配置 Router>en Router#config t Enter configuration commands, one per line.  End with CN

原创 BGP基礎配置

拓撲圖   實驗過程 1.       R1的預配置 Router>en Router#config t Enter configuration commands, one per line.  End with CNTL/Z

原创 VRRP基礎配置

拓撲圖   實驗過程   1.       pc的配置 Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z.

原创 路由重發布之ISIS和EIGRP

實驗拓撲圖   實驗過程 1. R1的預配置 Router>en Router#config t Enter configuration commands, one per line.  End with CNTL/Z. Ro

原创 OSPF外部路由彙總

拓撲圖   實驗過程 1.       R1的預配置 Router>en Router#config t Enter configuration commands, one per line.  End with CNTL/Z