實踐結果：
把WinXP安裝在SATA硬盤裏面，只要BISO裏面AHCI開啓，使用以下方法都不能成功（WinXP EN SP2 VOL）-（DELL INSPER 14R NoteBook）。安裝XP時關閉AHCI，安裝完畢只要啓動時開啓AHCI，就藍屏，不能進入系統（包括安全模式）。而先關閉AHCI，使用IDE模式進系統，在系統裏面更新驅動，也是一更新就藍屏。
最後實踐成功的方法是在安裝鏡像裏面添加sata驅動。可以參見博客中另外一篇帖子。
WinXP：
From what I'm aware the unofficial Intel SATA/AHCI/RAID motherboard-based controller fix for XP is not necessary anymore, because Intel finally enabled that feature natively in their drivers.
Note:
To install/test the Intel driver, it is recommended to uninstall/delete the unofficial driver (if any) first and then reboot.
Unofficial driver fix installs its files into the %windir%\IAHCI [%windir% = usually C:\WINDOWS] folder. Just delete all those files and reboot.
Therefore starting with Intel Storage Manager Driver version 9.6.0.1014 all one needs to do is:
1. Reboot.
2. Press Del, Esc, F1, F2, F3, F4 or F8 (see your motherboard documentation for specific key) to enter BIOS setup while your computer's initial POST (Power On Self Test) screen is still on -> change both settings below (if any) to match the values inside square brackets:
SATA RAID/AHCI Mode [AHCI]
SATA Port 0-3 Native Mode [Enabled]
Both these settings must be enabled *before* installing the driver in order for Intel setup to properly recognize AHCI/RAID hardware.
3. Reboot back to Windows.
4. Install current Intel Storage Manager Driver from here [11.2 MB, multilanguage].
This driver installs iastore.sys and enables AHCI/RAID modes if enabled hardware is detected at install time.
5. Reboot 1 last time.
This should (hopefully) work for every mobo based on Intel 9xx/3x/4x/5x chipset series.
Please see Intel ReadMe text for more info.
... And just in case the official Intel driver doesn't work, I'm keeping the unofficial driver fix at my site.
If any1 has problems with the mobo, SATA controllers or hard drives while AHCI is enabled, you can disable it easily:
go back into BIOS setup and disable/change any of those 2 settings [see #2 above].
Could disable both, wont't hurt anything, but this feature requires both enabled, otherwise cannot work.
PS:
I was also getting BSODs and STOP errors in XP [especially with AHCI enabled] with my old mobo [Gigabyte P35-DS3L], took me a while to figure out what was wrong, turned out to be a faulty capacitor. ;-(
I got a replacement [Gigabyte EP43-UD3L], and never looked back. Everything works 100% with or without AHCI enabled, even if overclocked. ;-)
___________________________________________
XP forums (super)mods...
Since this issue has been finally resolved, I propose to close this topic.
Thanks for caring.
HTH
Best wishes,
MDGx
其他的方法（在我機器上測試不成功）：
http://itbbs.pconline.com.cn/notebook/9405739.html
IDE 模式安裝 WinXP後，開啓 AHCI 模式的操作步驟：
1、Intel 芯片組
在Windows中打開設備管理器，IDE ATA/ATAPI 控制器 ———》 Intel XXX Serial ATA Storage Contraller ———》 右鍵 ———》 更新驅動程序軟件 ———》不要搜索，我要自己選擇要安裝的驅動程序 ———》 從磁盤安裝 ———》 指向製作的 F6 SATA 驅動軟盤（或者是從官網下載的ahci解壓文件） ———》 選擇正確的設備（i945芯片組選擇 AHCI ICH7M Driver，i965 芯片組選擇 AHCI ICH8M Driver）。
注：上述步驟也可以通過下載運行該文件的方式取代（http://esupport.acer.com.cn/portal/doc/KB/TM/TI/EnableAHCI(Intel).rar）複製鏈接，右鍵迅雷下載。
重啓電腦，按 F2 進入 BIOS，設定 SATA Mode 爲 AHCI Mode。保存退出。
進入系統後提示找到 PCI 設備。安裝 Intel AHCI 驅動即可。
2、 nForce610 芯片組 （AS4220、AS4520）
在Windows中打開設備管理器，IDE ATA/ATAPI 控制器 ———》 標準雙通道 PCI IDE 控制器 ———》 右鍵 ———》 更新驅動程序軟件 ———》 不要搜索，我要自己選擇要安裝的驅動程序 ———》 從磁盤安裝 ———》 指向 ChipSet 驅動中的 IDE\WinXP\sata_ide 目錄，並安裝驅動。
重啓電腦，按 F2 進入 BIOS，設定 SATA Mode 爲 AHCI Mode。保存退出。
Another：
1. 下載 “Intel Matrix Storage Manager驅動程序(Windows XP/Vista 32bit)”
給個地址，聯想官網的：http://driverdl.lenovo.com.cn/think/download/driver/dr1197539101703/7zim57ww.exe
2. 雙擊該程序，解壓縮到硬盤以下位置:C:\DRIVERS\WIN\IMSM
3. 先打開C:\DRIVERS\WIN\IMSM\PREPARE目錄, 雙擊install.cmd
4. 然後重啓計算機，進入BIOS,改爲AHCI。
5. 進入系統後會發現新硬件，手動選擇驅動位置，指向到C:\DRIVERS\WIN\IMSM目錄搜索安裝即可。
6. 再次重啓，OK
Win7：
http://neolee.com/pc/change-ide-mode-to-ahci-in-windows-xp-vista-and-7/
1. 進入註冊表regedit
2. 進入HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci
3. 將 start 項的值從3改爲0.
4. 重啓電腦，進入BIOS，改爲AHCI。啓動後會自動安裝驅動。
5. 再次重啓，OK
Win8：
1.先將BIOS裏的AHCI改回IDE開機 2.快捷鍵Win+R – 輸入regedit – 找到： HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci 刪除 StartOverride HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV 刪除 “StartOverride 3.重啓電腦進入BOIS開啓AHCI：找到 Integrated Peripherals ，將“SATA RAID/AHCI Mode”更改“AHCI”