Show Controllers E1 命令的講解

       純搬運工，從Cisco官網轉載，因爲很多專業術語不知如何翻譯，自己也不是很理解，希望以後能補充完整。Cisco官網文檔 Understanding the show controllers e1 command 編號：9160

______________________________________________________________________________________________-----

Show Controllers E1 命令用於顯示E1控制器的硬件狀態。

Show Controllers E1 輸出舉例

Bru#show controllers e1  
E1 0 is up.    
    Applique type is Channelized E1 ? balanced    
    No alarms detected.    
    Version info of Slot 0: HW: 2, Firmware: 4, PLD Rev: 2    
Manufacture Cookie is not programmed. 
Framing is CRC4, Line Code is HDB3, Clock Source is Line Primary. 
   Data in current interval (251 seconds elapsed):    
     0 Line Code Violations, 0 Path Code Violations    
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins    
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs    
Total Data (last 24 hours)    
    0 Line Code Violations, 0 Path Code Violations,    
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,    
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

E1 1 is down.    
    Applique type is Channelized E1 ? balanced    
    Transmitter is sending remote alarm.    
    Receiver has loss of signal.    
    Version info of Slot 0: HW: 2, Firmware: 4, PLD Rev: 2    
Manufacture Cookie is not programmed.    
Framing is CRC4, Line Code is HDB3, Clock Source is Line Secondary.    
  Data in current interval (200 seconds elapsed):    
       0 Line Code Violations, 0 Path Code Violations    
       0 Slip Secs, 200 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins    
       0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 200 Unavail Secs    
Total Data (last 24 hours)    
       0 Line Code Violations, 0 Path Code Violations,    
       0 Slip Secs, 86400 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,    
       0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs

E1 2 is administratively down.    
    Applique type is Channelized E1 ? balanced    
    Transmitter is sending remote alarm.    
    Receiver has loss of signal.    
    Version info of Slot 0: HW: 2, Firmware: 4, PLD Rev: 2    
Manufacture Cookie is not programmed.    
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.    
   Data in current interval (249 seconds elapsed):    
       0 Line Code Violations, 0 Path Code Violations    
       0 Slip Secs, 249 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins    
       0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 249 Unavail Secs    
  Total Data (last 24 hours)    
      0 Line Code Violations, 0 Path Code Violations,    
      0 Slip Secs, 86400 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,    
      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs

字段說明

E1 0 is up	顯示E1控制器的的狀態。 這個狀態可以是UP，Down 或 Administratively Down。打環時會顯示Locally looped 或remotely looped。
Applique Type	控制器的Applique Type 和 indicate 可以是Blanced 或 Unbalanced
Framing	默認是有CRC4校驗的
Line Code	默認E1線路的line code是HDB3
No Alarms detected	如監測到任何報警信息，會顯示在當前位置。可能會出現的報警信息有： Transmitter is sending remote alarm. Transmitter is sending alarm indication             signal (AIS)。 Receiver has loss of signal. Receiver is getting AIS. Receiver has loss of frame.  Receiver has remote alarm.  Receiver has no alarms.
Data in current interval(251 seconds elapsed)	Shows the current accumulation period, which           rolls into a 24 hour accumulation every 15             minutes. The accumulation period is from one             to 900 seconds. The oldest 15?minute period             falls off the back of the 24?hour accumulation             buffer.
Line Code Violations	Indicates the occurrence of either a Bipolar           Violation (BPV) or Excessive Zeros (EXZ)             error event.
Path Code Violations	Indicates a frame synchronization bit error in           the D4 and E1?no CRC formats, or a CRC             error in the Extended Superframe (ESF) and             E1?CRC formats.
Slip Secs	Indicates the replication or deletion of the           payload bits of a domestic trunk interface             (DS1) frame. A slip might happen when there             is a difference between the timing of a             synchronous receiving terminal and the             received signal.
Fr Loss Secs	Indicates the number of seconds an Out of           Frame (OOF) error is detected.
Line Err secs	Line Errored Seconds (LES) is a second in           which one or more Line Code Violation errors             are detected.
Degraded Mins	A degraded minute is one in which the           estimated error rate exceeds 1E?6 but does not             exceed 1E?3.
Errored secs	In ESF and E1 CRC links, an errored second is           a second in which one of the following defects             is detected: One or more Path Code Violations. One or more Controlled Slip events.  For SF and E1 no?CRC links, the presence of           Bipolar Violations also triggers an errored             second.
Bursty Err secs	A second with more than one but fewer than           320 Path Coding Violation errors, no Severely             Errored Frame defects and no detected             incoming AIS defects. Controlled slips are not             included in this parameter.
Severly Err Secs	For ESF signals, this is a second in which one           of the following defects is detected: 320 or more Path Code Violation             errors. One or more Out of Frame defects. An AIS defect. For E1?CRC signals, a second with one of the           following errors: 832 or more Path Code Violation             errors. One or more Out of Frame defects      For E1?nonCRC signals, this is a second with           2048 Line Code Violations or more. For D4             signals, this means a count of 1?second             intervals with Framing Errors, or an Out of             Frame defect, or 1544 Line Code Violations
Unavail Secs	For E1?nonCRC signals, this is a second with           2048 Line Code Violations or more. For D4             signals, this means a count of 1?second             intervals with Framing Errors, or an Out of             Frame defect, or 1544 Line Code Violations