cisco路由器基本實驗之一 靜態路由的配置（Boson NetSim

      如上的拓撲所示，（IP地址是我自己確定的，並且用ps寫上的，這樣看得比較清楚），現在需要完成的就是讓HostA能和HostB互相ping通，我在配置過程中遇到了一些問題，我都把容易出錯的地方註釋在下面的配置語句後面了，希望那些跟我一樣在網絡配置方面還處於初步的朋友一些幫助，還希望高手們不要見笑，並且給我多加指教，先謝謝了，好了，看我的具體配置如下：

router1的配置：

 

Press Enter to Start

Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname router1
router1(config)#interface e0
router1(config-if)#ip address 192.168.1.2 255.255.255.0
router1(config-if)#no shut
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
router1(config-if)#interface s0
router1(config-if)#ip address 192.168.2.1 255.255.255.0
router1(config-if)#clock rate 6400                   //clock rate是dce設備給dte設備提供時鐘頻率的，需要在dce裏面設置，而另外的一個路由器裏面則不用設置
router1(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
router1(config-if)#end
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
router1#config t
Enter configuration commands, one per line.  End with CNTL/Z.
router1(config)#ip route 192.168.3.0 255.255.255.0 192.168.2.1   //設定靜態路由
router1(config)#ip route 192.168.2.0 255.255.255.0 192.168.2.1
router1(config)#end
router1#copy running startup
Destination filename [startup-config]?
Building configuration...
[OK]

%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up

 

router2的配置：

 

Press Enter to Start

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface e0
Router(config-if)#end
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname router2
router2(config)#interface s0
router2(config-if)#ip address 192.168.2.2 255.255.255.0
router2(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
router2(config-if)#interface s0
router2(config-if)#interface e0
router2(config-if)#ip address 192.168.3.1 255.255.255.0
router2(config-if)#no shut
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
router2(config-if)#end
router2#config t
Enter configuration commands, one per line.  End with CNTL/Z.
router2(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.2
router2(config)#ip route 192.168.2.0 255.255.255.0 192.168.2.2
router2(config)#end
router2#copy running startup
Destination filename [startup-config]?
Building configuration...
[OK]

router2#ping 192.168.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
router2#ping 192.168.2.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
router2#ping 192.168.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms       //路由器之間試ping了一下，可以ping通，接下來配pc

 

pc1的配置如下：

 

Boson BOSS 5.0
Copyright 1998-2003 Boson Software, Inc.
Use the command help to get started

Press Enter to begin
C:>ipconfig /ip 192.168.1.1 255.255.255.0                     //此時尚未指定網關
C:>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:

Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 192.168.2.1:
     Packets: Sent = 5, Received = 0, Lost = 5 (100% loss),  //未指定網關時不能ping通router1的s0，我理解爲找不到出口，不知準確否
Approximate round trip times in milli-seconds:
     Minimum = 0ms, Maximum =  0ms, Average =  0ms

C:>ipconfig /dg 192.168.1.2                                  //指定網關爲與本機直連的router1的e0口
C:>ping 192.168.1.2
Pinging 192.168.1.2 with 32 bytes of data:

Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.1.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:

Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),      //指定網關後可以ping通s0口了
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.2
Pinging 192.168.2.2 with 32 bytes of data:

Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.3.1
Pinging 192.168.3.1 with 32 bytes of data:

Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.3.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.3.2
Pinging 192.168.3.2 with 32 bytes of data:

Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241
Reply from 192.168.3.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.3.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms                                       //可以ping通任意一臺設備的IP地址，實驗成功
C:>

 

pc2 的配置如下：

 

Boson BOSS 5.0
Copyright 1998-2003 Boson Software, Inc.
Use the command help to get started

Press Enter to begin
C:>
C:>ipconfig /ip 192.168.3.2 255.255.255.0
C:>ipconfig /dg 192.168.3.1                          //把IP和網關設好
C:>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241
Reply from 192.168.1.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.1.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.1.2
Pinging 192.168.1.2 with 32 bytes of data:

Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241
Reply from 192.168.1.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.1.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:

Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241
Reply from 192.168.2.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.2.2
Pinging 192.168.2.2 with 32 bytes of data:

Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241
Reply from 192.168.2.2: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.2.2:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms

C:>ping 192.168.3.1
Pinging 192.168.3.1 with 32 bytes of data:

Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241
Reply from 192.168.3.1: bytes=32 time=60ms TTL=241

Ping statistics for 192.168.3.1:     Packets: Sent = 5, Received = 5, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
     Minimum = 50ms, Maximum =  60ms, Average =  55ms  //可以ping通任意一臺設備的IP地址，實驗成功