交換機基本狀態:
switch: ;ROM狀態, 路由器是
rommon>
hostname> ;用戶模式
hostname# ;特權模式
hostname(config)# ;全局配置模式
hostname(config-if)# ; 接口狀態
交換機口令設置:
switch>enable ;進入特權模式
switch#config terminal ;進入全局配置模式
switch(config)#hostname <hostname> ;設置交換機的主機名
switch(config)#enable secret xxx ;設置特權加密口令爲 xxx
switch(config)#enable password xxx ;設置特權非密口令爲 xxx
switch(config)#line console 0 ;進控制檯口(Rs232)初始化
switch(config-line)#line vty 0 4 ;進入虛擬終端virtual tty
switch(config-line)#login ;允許登錄
switch(config-line)#password xx ;設置登錄口令xx
switch#exit ;返回命令
交換機VLAN設置:
switch#vlan database ;進入VLAN設置
switch(vlan)#vlan 2 ;建VLAN 2
switch(vlan)#no vlan 2 ;刪vlan 2
switch(config)#int f0/1 ;進入端口1
switch(config-if)#switchport access vlan 2 ;當前端口1加入VLAN 2
switch(config-if)#switchport mode trunk ;設置爲幹線
switch(config-if)#switchport trunk allowed vlan 1,2 ;設置允許的vlan
switch(config-if)#switchport trunk encap dot1q ;設置vlan 中繼
switch(config)#vtp domain <name> ; 設置發vtp域名
switch(config)#vtp password <word>
switch(config)#vtp mode server
switch(config)#vtp mode client
交換機設置IP地址:
switch(config)#interface vlan 1 ;進入vlan 1
switch(config-if)#ip address <IP> <mask> ;添加遠程登錄IP
switch(config)#ip default-gateway <IP> ;添加默認網關
switch#dir flash: ;查看內存
交換機顯示命令:
switch#write ;寫入保存
switch#show vtp
switch#show run ;查看當前配置信息
switch#show vlan ;看VLAN
switch#show interface ;顯示所有端口信息
switch#show int f0/0 ;顯示端口0的信息
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
路由器顯示命令:
router#show run ;顯示接口
router#show interface ;顯示接口
router#show ip route ;顯示路由
router#show cdp nei ;看鄰居
router#reload ;重新起動
設置口令:
router>enable ;進入特權模式
router#config terminal ;進入全局配置模式
router(config)#hostname <hostname> ;設置交換機的主機名
router(config)#enable secret xxx ;設置特權加密口令爲 xxx
router(config)#enable password xxx ;設置特權非密口令爲 xxx
router(config)#line console 0 ;進控制檯口(Rs232)初始化
router(config-line)#line vty 0 4 ;進入虛擬終端virtual tty
router(config-line)#login ;允許登錄
router(config-line)#password xx ;設置登錄口令xx
router(config)# (Ctrl+z) ; 返回特權模式
router#exit ;返回命令
配置IP地址:
router(config)#int s0/0 ;進行串Serail接口
router(config-if)#no shutdown ;起動接口
router(config-if)#clock rate 64000 ;設置時鐘
router(config-if)#ip address 10.1.1.1 255.255.0.0 ;設置IP地址和子網掩碼
router(config-if)#ip add 10.1.1.2 255.255.0.0 second;
router(config-if)#int f0/0.1 ; 進入子接口
router(config-subif.1)#ip address <ip><netmask> ;
router(config-subif.1)#encapsulation dot1q <n> ;
router(config)#config-register 0x2142 ;跳過配置文件
router(config)#config-register 0x2102 ;正常使用配置文件
router#reload ;重新引導
複製操作:
router#copy running-config startup-config ;存配置
router#copy running-config tftp ;上載
router#copy startup-config tftp
router#copy tftp flash: ;特權模式下升級IOS
router#copy tftp startup-config ;下載配置文件到nvram
ROM狀態:
Ctrl+Break ;進入ROM監控狀態
rommon>confreg 0x2142 ;跳過配置,26 36 45xx
rommon>confreg 0x2102 ;使用配置,恢復工作狀態
rommon>reset ;重新引導,等效於重開機
rommon>copy xmodem:<sname> flash:<dname> ;從console升級IOS
rommon>IP_ADDRESS=10.65.1.2 ;設置路由器IP
rommon>IP_SUBNET_MASK=255.255.0.0 ;設置路由器掩碼
rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服務器IP
rommon>TFTP_FILE=c2600.bin ;所要下載的文件
rommon>tftpdnld ;ROM監控狀態下升級IOS
rommon>dir flash: ;查看閃存中的內容
rommon>boot ;引導IOS
靜態路由:
ip route <ip-address> <subnet-mask> <gateway> 例:
router(config)#ip route 10.1.0.0 255.255.0.0 10.2.1.1
router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2
動態路由:
router(config)#ip routing ;啓動路由
router(config)#router rip ;啓動RIP路由協議。
router(config-router)#network <netid> ;配置範圍,有的支持all。
router(config-router)#negihbor <ip-address> ;點對點 幀中繼用。
幀中繼命令:
router(config)# frame-relay switching ;使能幀中繼交換
router(config-s0)# encapsulation frame-relay ;使能幀中繼
router(config-s0)# frame-relay intf-type DCE ;DCE端(需要配虛電路)
router(config-s0)# frame-relay local-dlci 20 ;配置虛電路號
基本訪問控制列表:
router(config)#access-list <number> permit|deny <source ip> <wild|any>
router(config)#interface <interface>
本文出自 51CTO.COM技術博客