Arduino红外发射的调频定时器设置
原博客格式更友好：http://www.straka.cn/blog/arduino-uno-infrared-emission-timer-setup/
网上了解了下ARDUINO的定时器、中断、PWM、舵机控制，红外收发等相关知识。尤其是仔细阅读了AVR atmega328p，也就是ARDUINO UNO的芯片手册的定时器部分，其中有两点：
- AT mega328p的定时器有3个，对应Arduino UNO板子，
- Timer0 对应 5、6引脚pwm, 8bit
- Timer1 对应 9、10引脚pwm, 16bit
- Timer2 对应 11、3引脚pwm, 8bit
- 舵机的pwm频率为50Hz / 20ms, 但是控制舵机需要的占空比比较小，为20ms中的5 ~ 2.5ms。
先讲讲红外发射的调频原理吧
那么根据1，由于红外发射需要38khz左右的载波频率，不过不用特别精确的38khz，所以红外收发的库里，
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 |
#define TIMER_RESET #define TIMER_ENABLE_PWM (TCCR2A |= _BV(COM2B1)) #define TIMER_DISABLE_PWM (TCCR2A &= ~(_BV(COM2B1))) #define TIMER_ENABLE_INTR (TIMSK2 = _BV(OCIE2A)) #define TIMER_DISABLE_INTR (TIMSK2 = 0) #define TIMER_INTR_NAME TIMER2_COMPA_vect
#define TIMER_CONFIG_KHZ(val) ({ \ const uint8_t pwmval = SYSCLOCK / 2000 / (val); \ TCCR2A = _BV(WGM20); \ TCCR2B = _BV(WGM22) | _BV(CS20); \ OCR2A = pwmval; \ OCR2B = pwmval / 3; \ })
#define TIMER_COUNT_TOP (SYSCLOCK * USECPERTICK / 1000000) |
假若是16M的晶振，根据上述代码和手册，WGM20和WGM22置1，所以Mode为5
那么就是pwm，phase correct模式，
主要意思就是，每周期在ocrA处达到计数顶部，触发中断，然后从0开始计数，由于不是到达顶部255溢出才从0开始重新计数，所以能实现相位的调整，而不再是fclk / prescale / 256的频率。因为CS20置位，所以预除数是1，即没有预除数prescale。
那么频率就是fout= fclk / ocrA / 2，除2是因为两个中断才完成电平翻转，形成载波的一个周期。
那我们很容易得到，如果我们想要38khz的频率，用16M晶振获取，需要设置OCRA为
16M/38k/2=210，那么实际频率 16m / 210 / 2 = 38095.238hz。
中断向量TIMER2_COMPA_vect的处理函数
中要做的就是根据要收发的消息，对载波进行调制，根据需要调制上载波或者去掉载波。
此处见代码，不详述。
C++
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 |
//+============================================================================= // Interrupt Service Routine - Fires every 50uS // TIMER2 interrupt code to collect raw data. // Widths of alternating SPACE, MARK are recorded in rawbuf. // Recorded in ticks of 50uS [microseconds, 0.000050 seconds] // 'rawlen' counts the number of entries recorded so far. // First entry is the SPACE between transmissions. // As soon as a the first [SPACE] entry gets long: // Ready is set; State switches to IDLE; Timing of SPACE continues. // As soon as first MARK arrives: // Gap width is recorded; Ready is cleared; New logging starts // ISR (TIMER_INTR_NAME) { TIMER_RESET;
// Read if IR Receiver -> SPACE [xmt LED off] or a MARK [xmt LED on] // digitalRead() is very slow. Optimisation is possible, but makes the code unportable uint8_t irdata = (uint8_t)digitalRead(irparams.recvpin);
irparams.timer++; // One more 50uS tick if (irparams.rawlen >= RAWBUF) irparams.rcvstate = STATE_OVERFLOW ; // Buffer overflow
switch(irparams.rcvstate) { //...................................................................... case STATE_IDLE: // In the middle of a gap if (irdata == MARK) { if (irparams.timer < GAP_TICKS) { // Not big enough to be a gap. irparams.timer = 0;
} else { // Gap just ended; Record duration; Start recording transmission irparams.overflow = false; irparams.rawlen = 0; irparams.rawbuf[irparams.rawlen++] = irparams.timer; irparams.timer = 0; irparams.rcvstate = STATE_MARK; } } break; //...................................................................... case STATE_MARK: // Timing Mark if (irdata == SPACE) { // Mark ended; Record time irparams.rawbuf[irparams.rawlen++] = irparams.timer; irparams.timer = 0; irparams.rcvstate = STATE_SPACE; } break; //...................................................................... case STATE_SPACE: // Timing Space if (irdata == MARK) { // Space just ended; Record time irparams.rawbuf[irparams.rawlen++] = irparams.timer; irparams.timer = 0; irparams.rcvstate = STATE_MARK;
} else if (irparams.timer > GAP_TICKS) { // Space // A long Space, indicates gap between codes // Flag the current code as ready for processing // Switch to STOP // Don't reset timer; keep counting Space width irparams.rcvstate = STATE_STOP; } break; //...................................................................... case STATE_STOP: // Waiting; Measuring Gap if (irdata == MARK) irparams.timer = 0 ; // Reset gap timer break; //...................................................................... case STATE_OVERFLOW: // Flag up a read overflow; Stop the State Machine irparams.overflow = true; irparams.rcvstate = STATE_STOP; break; }
#ifdef BLINKLED // If requested, flash LED while receiving IR data if (irparams.blinkflag) { if (irdata == MARK) if (irparams.blinkpin) digitalWrite(irparams.blinkpin, HIGH); // Turn user defined pin LED on else BLINKLED_ON() ; // if no user defined LED pin, turn default LED pin for the hardware on else if (irparams.blinkpin) digitalWrite(irparams.blinkpin, LOW); // Turn user defined pin LED on else BLINKLED_OFF() ; // if no user defined LED pin, turn default LED pin for the hardware on } #endif // BLINKLED } |
参考资料：
