# For more options and information see
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=23
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
start_x=1
gpu_mem=128
#enable_uart=0
dtoverlay=pi3-miniuart-bt
force_turbo=1
樹莓派3 配置文件conf 高分辨率 串口引腳重映射
發表評論
所有評論
還沒有人評論,想成為第一個評論的人麼? 請在上方評論欄輸入並且點擊發布.
相關文章
ROS報錯處理(持續更新)
li528405176
2018-08-27 19:57:03
在仿真環境下基於數據包和RGB-D相機運行ORB_SLAM2功能包
li528405176
2018-08-27 19:57:02
ROS Launch使用總結
倔强不倒翁
2018-08-27 19:46:30
譯:使用`tf`來配置你的機器人
tianyazh
2018-08-27 19:42:22
啓動ROS rviz出現`段錯誤(核心已轉儲)`問題的解決方法
tianyazh
2018-08-27 19:42:09
譯:ROS圖像和OpenCV圖像相互轉換
tianyazh
2018-08-27 19:41:52
譯:基於ROS發佈傳感器流數據
tianyazh
2018-08-27 19:41:51
譯:在ROS上發佈Odometry信息
tianyazh
2018-08-27 19:41:39
樹莓派Pi2安裝ROS Kinetic Kame開發環境(基於Ubuntu 16.04LTS)
一分--
2018-08-27 19:22:39
在Ubuntu16.04下photoneo相機驅動與ROS連接教程[兼容問題已解決]
豌豆生
2018-08-27 19:14:24
ROS編譯過程中錯誤解決
豌豆生
2018-08-27 19:14:24
在Ubuntu16.04下使用ur_modern_driver無法編譯成功的解決方法
豌豆生
2018-08-27 19:14:24
淺談ROS消息與服務——搭建簡單的服務端和客戶端
谁话沉香
2018-08-27 18:26:49
ROS實戰之節點發布/接收圖片
初生牛犊_GDUT
2018-08-27 14:26:52